 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Features * Utilizes the AVR(R) RISC Architecture * AVR - High-performance and Low-power RISC Architecture - 90 Powerful Instructions - Most Single Clock Cycle Execution - 32 x 8 General-purpose Working Registers - Up to 4 MIPS Throughput at 4 MHz Nonvolatile Program Memory - 2K Bytes of Flash Program Memory - Endurance: 1,000 Write/Erase Cycles - Programming Lock for Flash Program Data Security Peripheral Features - Interrupt and Wake-up on Low-level Input - One 8-bit Timer/Counter with Separate Prescaler - On-chip Analog Comparator - Programmable Watchdog Timer with On-chip Oscillator - Built-in High-current LED Driver with Programmable Modulation Special Microcontroller Features - Low-power Idle and Power-down Modes - External and Internal Interrupt Sources - Power-on Reset Circuit with Programmable Start-up Time - Internal Calibrated RC Oscillator Power Consumption at 1 MHz, 2V, 25C - Active: 3.0 mA - Idle Mode: 1.2 mA - Power-down Mode: <1 A I/O and Packages - 11 Programmable I/O Lines, 8 Input Lines and a High-current LED Driver - 28-lead PDIP, 32-lead TQFP, and 32-pad MLF Operating Voltages - VCC: 1.8V - 5.5V for the ATtiny28V - VCC: 2.7V - 5.5V for the ATTINY28L Speed Grades - 0 - 1.2 MHz for the ATtiny28V - 0 - 4 MHz For the ATTINY28L * * * 8-bit Microcontroller with 2K Bytes of Flash ATTINY28L ATtiny28V * * * * Pin Configurations PDIP TQFP/MLF PD2 PD1 PD0 RESET PA0 PA1 PA3 PA2 (IR) 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 9 10 11 12 13 14 15 16 PD5 PD6 PD7 (AIN0) PB0 (AIN1) PB1 (T0) PB2 (INT0) PB3 (INT1) PB4 RESET PD0 PD1 PD2 PD3 PD4 VCC GND XTAL1 XTAL2 PD5 PD6 PD7 (AIN0) PB0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 PA0 PA1 PA3 PA2 (IR) PB7 PB6 GND NC VCC PB5 PB4 (INT1) PB3 (INT0) PB2 (T0) PB1 (AIN1) PD3 PD4 NC VCC GND NC XTAL1 XTAL2 1 2 3 4 5 6 7 8 PB7 PB6 NC GND NC NC VCC PB5 Rev. 1062E-10/01 1 Description The ATtiny28 is a low-power CMOS 8-bit microcontroller based on the AVR RISC architecture. By executing powerful instructions in a single clock cycle, the ATtiny28 achieves throughputs approaching 1 MIPS per MHz, allowing the system designer to optimize power consumption versus processing speed. The AVR core combines a rich instruction set with 32 general-purpose working registers. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers. Figure 1. The ATtiny28 Block Diagram VCC 8-BIT DATA BUS INTERNAL OSCILLATOR GND PROGRAM COUNTER STACK POINTER WATCHDOG TIMER MCU CONTROL REGISTER TIMER/ COUNTER TIMING AND CONTROL RESET OSCILLATOR XTAL1 XTAL2 INTERNAL CALIBRATED OSCILLATOR Block Diagram PROGRAM FLASH INSTRUCTION REGISTER INSTRUCTION DECODER HARDWARE STACK GENERAL PURPOSE REGISTERS Z INTERRUPT UNIT CONTROL LINES ALU STATUS REGISTER HARDWARE MODULATOR PROGRAMMING LOGIC ANALOG COMPARATOR DATA REGISTER PORTB DATA REGISTER PORTD DATA DIR REG. PORTD DATA REGISTER PORTA CONTROL PORTA REGISTER + - PORTB PORTD PORTA The ATtiny28 provides the following features: 2K bytes of Flash, 11 general-purpose I/O lines, 8 input lines, a high-current LED driver, 32 general-purpose working registers, an 8-bit timer/counter, internal and external interrupts, programmable Watchdog Timer with internal oscillator and 2 software-selectable power-saving modes. The Idle Mode stops the CPU while allowing the timer/counter and interrupt system to continue functioning. The Power-down mode saves the register contents but freezes the oscillator, disabling all other chip functions until the next interrupt or hardware reset. The wake-up or inter- 2 ATTINY28L/V 1062E-10/01 ATTINY28L/V rupt on low-level input feature enables the ATtiny28 to be highly responsive to external events, still featuring the lowest power consumption while in the power-down modes. The device is manufactured using Atmel's high-density, nonvolatile memory technology. By combining an enhanced RISC 8-bit CPU with Flash on a monolithic chip, the Atmel ATtiny28 is a powerful microcontroller that provides a highly flexible and cost-effective solution to many embedded control applications. The ATtiny28 AVR is supported with a full suite of program and system development tools including: macro assemblers, program debugger/simulators, in-circuit emulators and evaluation kits. Pin Descriptions VCC GND Port A (PA3..PA0) Supply voltage pin. Ground pin. Port A is a 4-bit I/O port. PA2 is output-only and can be used as a high-current LED driver. At VCC = 2.0V, the PA2 output buffer can sink 25 mA. PA3, PA1 and PA0 are bi-directional I/O pins with internal pull-ups (selected for each bit). The port pins are tristated when a reset condition becomes active, even if the clock is not running. Port B is an 8-bit input port with internal pull-ups (selected for all Port B pins). Port B pins that are externally pulled low will source current if the pull-ups are activated. Port B also serves the functions of various special features of the ATtiny28 as listed on page 39. If any of the special features are enabled, the pull-up(s) on the corresponding pin(s) is automatically disabled. The port pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port D (PD7..PD0) Port D is an 8-bit I/O port. Port pins can provide internal pull-up resistors (selected for each bit). The port pins are tri-stated when a reset condition becomes active, even if the clock is not running. Input to the inverting oscillator amplifier and input to the internal clock operating circuit. Output from the inverting oscillator amplifier. Reset input. An external reset is generated by a low level on the RESET pin. Reset pulses longer than 50 ns will generate a reset, even if the clock is not running. Shorter pulses are not guaranteed to generate a reset. Port B (PB7..PB0) XTAL1 XTAL2 RESET 3 1062E-10/01 Clock Options The device has the following clock source options, selectable by Flash Fuse bits as shown in Table 1. Table 1. Device Clocking Option Select Clock Option External Crystal/Ceramic Resonator External Low-frequency Crystal External RC Oscillator Internal RC Oscillator External Clock Note: "1" means unprogrammed, "0" means programmed. CKSEL3..0 1111 - 1010 1001 - 1000 0111 - 0101 0100 - 0010 0001 - 0000 The various choices for each clocking option give different start-up times as shown in Table 5 on page 14. Internal RC Oscillator The internal RC oscillator option is an on-chip calibrated oscillator running at a nominal frequency of 1.2 MHz. If selected, the device can operate with no external components. The device is shipped with this option selected. XTAL1 and XTAL2 are input and output, respectively, of an inverting amplifier, which can be configured for use as an on-chip oscillator, as shown in Figure 2. Either a quartz crystal or a ceramic resonator may be used. When the INTCAP fuse is programmed, internal load capacitors with typical values 50 pF are connected between XTAL1/XTAL2 and ground. Figure 2. Oscillator Connections MAX 1 HC BUFFER HC Crystal Oscillator C2 C1 XTAL2 XTAL1 GND Note: 1. When using the MCU oscillator as a clock for an external device, an HC buffer should be connected as indicated in the figure. 4 ATTINY28L/V 1062E-10/01 ATTINY28L/V External Clock To drive the device from an external clock source, XTAL2 should be left unconnected while XTAL1 is driven as shown in Figure 3. Figure 3. External Clock Drive Configuration NC EXTERNAL OSCILLATOR SIGNAL XTAL2 XTAL1 GND External RC Oscillator For timing insensitive applications, the external RC configuration shown in Figure 4 can be used. For details on how to choose R and C, see Table 25 on page 54. Figure 4. External RC Configuration VCC R NC XTAL2 XTAL1 C GND 5 1062E-10/01 Architectural Overview The fast-access register file concept contains 32 x 8-bit general-purpose working registers with a single clock cycle access time. This means that during one single clock cycle, one ALU (Arithmetic Logic Unit) operation is executed. Two operands are output from the register file, the operation is executed, and the result is stored back in the register file - in one clock cycle. Two of the 32 registers can be used as a 16-bit pointer for indirect memory access. This pointer is called the Z-pointer and can address the register file and the Flash program memory. Figure 5. The ATtiny28 AVR RISC Architecture Data Bus 8-bit 1K x 16 Program Flash Program Counter Status and Test 32 x 8 General Purpose Registrers Z Control Registrers Interrupts Unit 8-bit Timer/Counter Watchdog Timer Analog Comparator 20 I/O Lines Instruction Register Instruction Decoder ALU Control Lines The ALU supports arithmetic and logic functions between registers or between a constant and a register. Single register operations are also executed in the ALU. Figure 5 shows the ATtiny28 AVR RISC microcontroller architecture. The AVR uses a Harvard architecture concept - with separate memories and buses for program and data memories. The program memory is accessed with a two-stage pipeline. While one instruction is being executed, the next instruction is pre-fetched from the program memory. This concept enables instructions to be executed every clock cycle. The program memory is reprogrammable Flash memory. With the relative jump and relative call instructions, the whole 1K address space is directly accessed. All AVR instructions have a single 16-bit word format, meaning that every program memory address contains a single 16-bit instruction. During interrupts and subroutine calls, the return address program counter (PC) is stored on the stack. The stack is a 3-level-deep hardware stack dedicated for subroutines and interrupts. The I/O memory space contains 64 addresses for CPU peripheral functions such as Control Registers, Timer/Counters and other I/O functions. The memory spaces in the AVR architecture are all linear and regular memory maps. A flexible interrupt module has its control registers in the I/O space with an additional global interrupt enable bit in the status register. All the different interrupts have a sepa- 6 ATTINY28L/V 1062E-10/01 ATTINY28L/V r a te i nt er r up t v e c to r i n t h e i n te r r u pt v ec t or t a bl e at th e b e gi n ni n g of th e program memory. The different interrupts have priority in accordance with their interrupt vector position. The lower the interrupt vector address, the higher the priority. General-purpose Register File Figure 6 shows the structure of the 32 general-purpose registers in the CPU. Figure 6. AVR CPU General-purpose Working Registers 7 R0 R1 R2 General Purpose Working Registers ... ... R28 R29 R30 (Z-Register low byte) R31(Z-Register high byte) 0 All the register operating instructions in the instruction set have direct and single cycle access to all registers. The only exception are the five constant arithmetic and logic instructions SBCI, SUBI, CPI, ANDI and ORI between a constant and a register and the LDI instruction for load immediate constant data. These instructions apply to the second half of the registers in the register file - R16..R31. The general SBC, SUB, CP, AND, OR and all other operations between two registers or on a single register apply to the entire register file. Registers 30 and 31 form a 16-bit pointer (the Z-pointer), which is used for indirect Flash memory and register file access. When the register file is accessed, the contents of R31 are discarded by the CPU. ALU - Arithmetic Logic Unit The high-performance AVR ALU operates in direct connection with all the 32 generalpurpose working registers. Within a single clock cycle, ALU operations between registers in the register file are executed. The ALU operations are divided into three main categories - arithmetic, logic and bit functions. Some microcontrollers in the AVR product family feature a hardware multiplier in the arithmetic part of the ALU. The ATtiny28 contains 2K bytes of on-chip Flash memory for program storage. Since all instructions are single 16-bit words, the Flash is organized as 1K x 16 words. The Flash memory has an endurance of at least 1,000 write/erase cycles. The ATtiny28 program counter is 10 bits wide, thus addressing the 1K word Flash program memory. See page 44 for a detailed description of Flash data downloading. Downloadable Flash Program Memory Program and Data Addressing Modes The ATtiny28 AVR RISC microcontroller supports powerful and efficient addressing modes. This section describes the different addressing modes supported in the ATtiny28. In the figures, OP means the operation code part of the instruction word. To simplify, not all figures show the exact location of the addressing bits. 7 1062E-10/01 Register Direct, Single Register Rd Figure 7. Direct Single Register Addressing The operand is contained in register d (Rd). Register Indirect Figure 8. Indirect Register Addressing REGISTERFILE 0 Z-Register 30 31 The register accessed is the one pointed to by the Z-register (R31, R30). Register Direct, Two Registers Rd and Rr Figure 9. Direct Register Addressing, Two Registers Operands are contained in register r (Rr) and d (Rd). The result is stored in register d (Rd). 8 ATTINY28L/V 1062E-10/01 ATTINY28L/V I/O Direct Figure 10. I/O Direct Addressing Operand address is contained in six bits of the instruction word. n is the destination or source register address. Relative Program Addressing, RJMP and RCALL Figure 11. Relative Program Memory Addressing PROGRAM MEMORY 15 PC 0 $000 +1 15 OP 12 11 k 0 $3FF Program execution continues at address PC + k + 1. The relative address k is -2048 to 2047. Constant Addressing Using the LPM Instruction Figure 12. Code Memory Constant Addressing PROGRAM MEMORY $000 15 Z-REGISTER 10 $3FF Constant byte address is specified by the Z-register contents. The 15 MSBs select word address (0 - 1K), and LSB selects low byte if cleared (LSB = 0) or high byte if set (LSB = 1). 9 1062E-10/01 Subroutine and Interrupt Hardware Stack The ATtiny28 uses a 3-level-deep hardware stack for subroutines and interrupts. The hardware stack is 10 bits wide and stores the program counter (PC) return address while subroutines and interrupts are executed. RCALL instructions and interrupts push the PC return address onto stack level 0, and the data in the other stack levels 1 - 2 are pushed one level deeper in the stack. When a RET or RETI instruction is executed the returning PC is fetched from stack level 0, and the data in the other stack levels 1 - 2 are popped one level in the stack. If more than three subsequent subroutine calls or interrupts are executed, the first values written to the stack are overwritten. Memory Access and Instruction Execution Timing This section describes the general access timing concepts for instruction execution and internal memory access. The AVR CPU is driven by the System Clock, directly generated from the external clock crystal for the chip. No internal clock division is used. Figure 13 shows the parallel instruction fetches and instruction executions enabled by the Harvard architecture and the fast-access register file concept. This is the basic pipelining concept to obtain up to 1 MIPS per MHz with the corresponding unique results for functions per cost, functions per clocks and functions per power unit. Figure 13. The Parallel Instruction Fetches and Instruction Executions T1 T2 T3 T4 System Clock O 1st Instruction Fetch 1st Instruction Execute 2nd Instruction Fetch 2nd Instruction Execute 3rd Instruction Fetch 3rd Instruction Execute 4th Instruction Fetch Figure 14 shows the internal timing concept for the register file. In a single clock cycle an ALU operation using two register operands is executed, and the result is stored back to the destination register. Figure 14. Single Cycle ALU Operation T1 T2 T3 T4 System Clock O Total Execution Time Register Operands Fetch ALU Operation Execute Result Write Back 10 ATTINY28L/V 1062E-10/01 ATTINY28L/V I/O Memory The I/O space definition of the ATtiny28 is shown in Table 2. Table 2. ATtiny28 I/O Space Address Hex $3F $1B $1A $19 $16 $12 $11 $10 $08 $07 $06 $05 $04 $03 $02 $01 $00 Note: Name SREG PORTA PACR PINA PINB PORTD DDRD PIND ACSR MCUCS ICR IFR TCCR0 TCNT0 MODCR WDTCR OSCCAL Function Status Register Data Register, Port A Port A Control Register Input Pins, Port A Input Pins, Port B Data Register, Port D Data Direction Register, Port D Input Pins, Port D Analog Comparator Control and Status Register MCU Control and Status Register Interrupt Control Register Interrupt Flag Register Timer/Counter0 Control Register Timer/Counter0 (8-bit) Modulation Control Register Watchdog Timer Control Register Oscillator Calibration Register Reserved and unused locations are not shown in the table. All ATtiny28 I/O and peripherals are placed in the I/O space. The I/O locations are accessed by the IN and OUT instructions transferring data between the 32 general-purpose working registers and the I/O space. I/O registers within the address range $00 $1F are directly bit-accessible using the SBI and CBI instructions. In these registers, the value of single bits can be checked by using the SBIS and SBIC instructions. Refer to the Instruction Set section for more details. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses should never be written. The I/O and peripherals control registers are explained in the following sections. Status Register - SREG The AVR status register (SREG) at I/O space location $3F is defined as: Bit $3F Read/Write Initial Value 7 I R/W 0 6 T R/W 0 5 H R/W 0 4 S R/W 0 3 V R/W 0 2 N R/W 0 1 Z R/W 0 0 C R/W 0 SREG * Bit 7 - I: Global Interrupt Enable The global interrupt enable bit must be set (one) for the interrupts to be enabled. The individual interrupt enable control is then performed in separate control registers. If the global interrupt enable register is cleared (zero), none of the interrupts are enabled independent of the individual interrupt enable settings. The I-bit is cleared by hardware after 11 1062E-10/01 an interrupt has occurred, and is set by the RETI instruction to enable subsequent interrupts. * Bit 6 - T: Bit Copy Storage The bit copy instructions BLD (Bit LoaD) and BST (Bit STore) use the T-bit as source and destination for the operated bit. A bit from a register in the register file can be copied into T by the BST instruction, and a bit in T can be copied into a bit in a register in the register file by the BLD instruction. * Bit 5 - H: Half-carry Flag The half-carry flag H indicates a half-carry in some arithmetic operations. See the Instruction Set description for detailed information. * Bit 4 - S: Sign Bit, S = N V The S-bit is always an exclusive or between the negative flag N and the two's complement overflow flag V. See the Instruction Set description for detailed information. * Bit 3 - V: Two's Complement Overflow Flag The two's complement overflow flag V supports two's complement arithmetic. See the Instruction Set description for detailed information. * Bit 2 - N: Negative Flag The negative flag N indicates a negative result from an arithmetical or logical operation. See the Instruction Set description for detailed information. * Bit 1 - Z: Zero Flag The zero flag Z indicates a zero result from an arithmetical or logical operation. See the Instruction Set description for detailed information. * Bit 0 - C: Carry Flag The carry flag C indicates a carry in an arithmetical or logical operation. See the Instruction Set description for detailed information. Note that the status register is not automatically stored when entering an interrupt routine and restored when returning from an interrupt routine. This must be handled by software. Reset and Interrupt Handling The ATtiny28 provides five different interrupt sources. These interrupts and the reset vector each have a separate program vector in the program memory space. All the interrupts are assigned to individual enable bits. In order to enable the interrupt, both the individual enable bit and the I-bit in the status register (SREG) must be set to one. The lowest addresses in the program memory space are automatically defined as the Reset and Interrupt vectors. The complete list of vectors is shown in Table 3. The list also determines the priority levels of the different interrupts. The lower the address, the higher the priority level. RESET has the highest priority, and next is INT0 - the External Interrupt Request 0. 12 ATTINY28L/V 1062E-10/01 ATTINY28L/V Table 3. Reset and Interrupt Vectors Vector No. 1 2 3 4 5 6 Program Address $000 $001 $002 $003 $004 $005 Source RESET INT0 INT1 Input Pins TIMER0, OVF0 ANA_COMP Interrupt Definition Hardware Pin, Power-on Reset and Watchdog Reset External Interrupt Request 0 External Interrupt Request 1 Low-level Input on Port B Timer/Counter0 Overflow Analog Comparator The most typical and general program setup for the Reset and Interrupt vector addresses are: Address $000 $001 $002 $003 $004 $005 ; $006 ... MAIN: ... Reset Sources The ATtiny28 provides three sources of reset: * * * Power-on Reset. The MCU is reset when the supply voltage is below the Power-on Reset threshold (VPOT). External Reset. The MCU is reset when a low level is present on the RESET pin for more than 50 ns. Watchdog Reset. The MCU is reset when the Watchdog Timer period expires and the Watchdog is enabled. During reset, all I/O registers are then set to their initial values and the program starts execution from address $000. The instruction placed in address $000 must be an RJMP (relative jump) instruction to the reset handling routine. If the program never enables an interrupt source, the interrupt vectors are not used, and regular program code can be placed at these locations. The circuit diagram in Figure 15 shows the reset logic. Table 4 defines the timing and electrical parameters of the reset circuitry. 13 1062E-10/01 Figure 15. Reset Logic DATA BUS MCU Control and Status Register (MCUCS) PORF EXTRF WDRF VCC 100 - 500K RESET Reset Circuit Watchdog Timer On-chip RC Oscillator CK COUNTER RESET Power-on Reset Circuit S Q R CKSEL[3..0] Delay Counters Full Table 4. Reset Characteristics Symbol VPOT(1) VRST Note: Parameter Power-on Reset Threshold Voltage (rising) Power-on Reset Threshold Voltage (falling) RESET Pin Threshold Voltage Min 1.0 0.4 Typ 1.4 0.6 0.6 VCC Max 1.8 0.8 Unit V V V 1. The Power-on Reset will not work unless the supply voltage has been below VPOT (falling). Table 5. ATtiny28 Clock Options and Start-up Time CKSEL3..0 1111 1110 1101 1100 1011 1010 1001 1000 0111 0110 0101 Clock Source External Crystal/Ceramic Resonator (1) Start-up Time at 2.7V 1K CK 4.2 ms + 1K CK 67 ms + 1K CK 16K CK 4.2 ms + 16K CK 67 ms + 16K CK 67 ms + 1K CK 67 ms + 32K CK 6 CK 4.2 ms + 6 CK 67 ms + 6 CK External Crystal/Ceramic Resonator(1) External Crystal/Ceramic Resonator(1) External Crystal/Ceramic Resonator External Crystal/Ceramic Resonator External Crystal/Ceramic Resonator External Low-frequency Crystal External Low-frequency Crystal External RC Oscillator External RC Oscillator External RC Oscillator 14 ATTINY28L/V 1062E-10/01 INTERNAL RESET ATTINY28L/V Table 5. ATtiny28 Clock Options and Start-up Time (Continued) CKSEL3..0 0100 0011 0010 0001 Note: Clock Source Internal RC Oscillator Internal RC Oscillator Internal RC Oscillator External Clock Start-up Time at 2.7V 6 CK 4.2 ms + 6 CK 67 ms + 6 CK 6 CK 0000 External Clock 4.2 ms + 6 CK 1. Due to limited number of clock cycles in the start-up period, it is recommended that ceramic resonator be used. This table shows the start-up times from reset. From Power-down mode, only the clock counting part of the start-up time is used. The Watchdog oscillator is used for timing the real-time part of the start-up time. The number WDT oscillator cycles used for each time-out is shown in Table 6. Table 6. Number of Watchdog Oscillator Cycles Time-out 4.2 ms 67 ms Number of Cycles 1K 16K The frequency of the Watchdog oscillator is voltage-dependent, as shown in the section "Typical Characteristics" on page 55. The device is shipped with CKSEL = 0010. Power-on Reset A Power-on Reset (POR) pulse is generated by an on-chip detection circuit. The detection level is nominally 1.4V. The POR is activated whenever VCC is below the detection level. The POR circuit can be used to trigger the start-up reset, as well as detect a failure in supply voltage. The Power-on Reset (POR) circuit ensures that the device is reset from power-on. Reaching the Power-on Reset threshold voltage invokes a delay counter, which determines the delay for which the device is kept in RESET after V CC rise. The time-out period of the delay counter can be defined by the user through the CKSEL fuses. The different selections for the delay period are presented in Table 5. The RESET signal is activated again, without any delay, when the VCC decreases below detection level. See Figure 16. If the built-in start-up delay is sufficient, RESET can be connected to VCC directly or via an external pull-up resistor. By holding the RESET pin low for a period after VCC has been applied, the Power-on Reset period can be extended. Refer to Figure 17 for a timing example of this. 15 1062E-10/01 Figure 16. MCU Start-up, RESET Tied to VCC. VCC VPOT RESET VRST TIME-OUT tTOUT INTERNAL RESET Figure 17. MCU Start-up, RESET Controlled Externally VCC VPOT RESET VRST TIME-OUT tTOUT INTERNAL RESET External Reset An external reset is generated by a low level on the RESET pin. Reset pulses longer than 50 ns will generate a reset, even if the clock is not running. Shorter pulses are not guaranteed to generate a reset. When the applied voltage reaches the Reset Threshold Voltage (VRST) on its positive edge, the delay timer starts the MCU after the Time-out period (tTOUT) has expired. Figure 18. External Reset during Operation VCC RESET VRST TIME-OUT tTOUT INTERNAL RESET 16 ATTINY28L/V 1062E-10/01 ATTINY28L/V Watchdog Reset When the Watchdog times out, it will generate a short reset pulse of 1 XTAL cycle duration. On the falling edge of this pulse, the delay timer starts counting the Time-out period (tTOUT). Refer to page 26 for details on operation of the Watchdog. Figure 19. Watchdog Reset during Operation MCU Control and Status Register - MCUCS The MCU Control and Status Register contains control and status bits for general MCU functions. Bit $07 Read/Write Initial Value 7 PLUPB R/W 0 6 - R 0 5 SE R/W 0 4 SM R/W 0 3 WDRF R/W See Bit Desc. 2 - R 0 1 EXTRF R/W 0 PORF R/W MCUCS See Bit Description * Bit 7 - PLUPB: Pull-up Enable Port B When the PLUPB bit is set (one), pull-up resistors are enabled on all Port B input pins. When PLUPB is cleared, the pull-ups are disabled. If any of the special functions of Port B is enabled, the corresponding pull-up(s) is disabled, independent of the value of PLUPB. * Bit 6 - Res: Reserved Bit This bit is a reserved bit in the ATtiny28 and always reads as zero. * Bit 5 - SE: Sleep Enable The SE bit must be set (one) to make the MCU enter the sleep mode when the SLEEP instruction is executed. To avoid the MCU entering the sleep mode unless it is the programmer's purpose, it is recommended to set the Sleep Enable SE bit just before the execution of the SLEEP instruction. * Bit 4 - SM: Sleep Mode This bit selects between the two available sleep modes. When SM is cleared (zero), Idle Mode is selected as sleep mode. When SM is set (one), Power-down mode is selected as sleep mode. For details, refer to "Sleep Modes" below. * Bit 3 - WDRF: Watchdog Reset Flag This bit is set if a Watchdog reset occurs. The bit is cleared by a Power-on Reset, or by writing a logical "0" to the flag. * Bit 2 - Res: Reserved Bit This bit is a reserved bit in the ATtiny28 and always reads as zero. 17 1062E-10/01 * Bit 1 - EXTRF: External Reset Flag This bit is set if an external reset occurs. The bit is cleared by a Power-on Reset, or by writing a logical "0" to the flag. * Bit 0 - PORF: Power-on Reset Flag This bit is set if a Power-on Reset occurs. The bit is cleared by writing a logical "0" to the flag. To make use of the reset flags to identify a reset condition, the user should read and then clear the flag bits in MCUCS as early as possible in the program. If the register is cleared before another reset occurs, the source of the reset can be found by examining the reset flags. Interrupt Handling The ATtiny28 has one 8-bit Interrupt Control Register (ICR). When an interrupt occurs, the Global Interrupt Enable I-bit is cleared (zero) and all interrupts are disabled. The user software can set (one) the I-bit to enable nested interrupts. The I-bit is set (one) when a Return from Interrupt instruction (RETI) is executed. When the program counter is vectored to the actual interrupt vector in order to execute the interrupt handling routine, hardware clears the corresponding flag that generated the interrupt. Some of the interrupt flags can also be cleared by writing a logical "1" to the flag bit position(s) to be cleared. If an interrupt condition occurs when the corresponding interrupt enable bit is cleared (zero), the interrupt flag will be set and remembered until the interrupt is enabled or the flag is cleared by software. If one or more interrupt conditions occur when the global interrupt enable bit is cleared (zero), the corresponding interrupt flag(s) will be set and remembered until the global interrupt enable bit is set (one), and will be executed by order of priority. Note that external level interrupt does not have a flag and will only be remembered for as long as the interrupt condition is active. Note that the status register is not automatically stored when entering an interrupt routine and restored when returning from an interrupt routine. This must be handled by software. Interrupt Response Time The interrupt execution response for all the enabled AVR interrupts is four clock cycles minimum. After four clock cycles the program vector address for the actual interrupt handling routine is executed. During this 4-clock-cycle period, the program counter (10 bits) is pushed onto the stack. The vector is normally a relative jump to the interrupt routine, and this jump takes two clock cycles. If an interrupt occurs during execution of a multi-cycle instruction, this instruction is completed before the interrupt is served. If an interrupt occurs when the MCU is in sleep mode, the interrupt execution response time is increased by four clock cycles. A return from an interrupt handling routine takes four clock cycles. During these four clock cycles, the program counter (10 bits) is popped back from the stack, and the I-flag in SREG is set. When AVR exits from an interrupt, it will always return to the main program and execute one more instruction before any pending interrupt is served. 18 ATTINY28L/V 1062E-10/01 ATTINY28L/V Interrupt Control Register - ICR Bit $06 Read/Write Initial Value 7 INT1 R/W 0 6 INT0 R/W 0 5 LLIE R/W 0 4 TOIE0 R/W 0 3 ISC11 R/W 0 2 ISC10 R/W 0 1 ISC01 R/W 0 0 ISC00 R/W 0 ICR * Bit 7 - INT1: External Interrupt Request 1 Enable When the INT1 bit is set (one) and I-bit in the Status Register (SREG) is set (one), the external pin interrupt 1 is enabled. The interrupt Sense Control1 bits 1/0 (ISC11 and ISC10) define whether the external interrupt is activated on rising or falling edge, on pin change or low level of the INT1 pin. The corresponding interrupt of External Interrupt Request 1 is executed from program memory address $002. See also "External Interrupt". * Bit 6 - INT0: External Interrupt Request 0 Enable When the INT0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), the external pin interrupt 0 is enabled. The interrupt Sense Control0 bits 1/0 (ISC01 and ISC00) define whether the external interrupt is activated on rising or falling edge, on pin change or low level of the INT0 pin. The corresponding interrupt of External Interrupt Request 0 is executed from program memory address $001. See also "External Interrupt". * Bit 5 - LLIE: Low-level Input Interrupt Enable When the LLIE is set (one) and the I-bit in the status register (SREG) is set (one), the interrupt on low-level input is activated. Any of the Port B pins pulled low will then cause an interrupt. However, if any Port B pins are used for other special features, these pins will not trigger the interrupt. The corresponding interrupt of Low-level Input Interrupt Request is executed from program memory address $003. See also "Low-level Input Interrupt". * Bit 4 - TOIE0: Timer/Counter0 Overflow Interrupt Enable When the TOIE0 bit is set (one) and the I-bit in the Status Register is set (one), the Timer/Counter0 Overflow Interrupt is enabled. The corresponding interrupt (at vector $004) is executed if an overflow in Timer/Counter0 occurs, i.e., when the TOV0 bit is set in the Interrupt Flag Register (IFR). * Bits 3, 2 - ISC11, ISC10: Interrupt Sense Control 1 Bit 1 and Bit 0 The External Interrupt 1 is activated by the external pin INT1 if the SREG I-flag and the corresponding interrupt enable are set. The level and edges on the external INT1 pin that activate the interrupt are defined in Table 7. 19 1062E-10/01 Table 7. Interrupt 1 Sense Control ISC11 0 0 1 1 Note: ISC10 0 1 0 1 Description The low level of INT1 generates an interrupt request. Any change on INT1 generates an interrupt request. The falling edge of INT1 generates an interrupt request. The rising edge of INT1 generates an interrupt request. When changing the ISC11/ISC10 bits, INT1 must be disabled by clearing its Interrupt Enable bit. Otherwise, an interrupt can occur when the bits are changed. * Bits 1, 0 - ISC01, ISC00: Interrupt Sense Control 0 Bit 1 and Bit 0 The External Interrupt 0 is activated by the external pin INT0 if the SREG I-flag and the corresponding interrupt enable are set. The level and edges on the external INT0 pin that activate the interrupt are defined in Table 8. Table 8. Interrupt 0 Sense Control ISC01 0 0 1 1 Note: ISC00 0 1 0 1 Description The low level of INT0 generates an interrupt request. Any change on INT0 generates an interrupt request. The falling edge of INT0 generates an interrupt request. The rising edge of INT0 generates an interrupt request. When changing the ISC01/ISC00 bits, INT0 must be disabled by clearing its Interrupt Enable bit. Otherwise, an interrupt can occur when the bits are changed. The value on the INT pins are sampled before detecting edges. If edge interrupt is selected, pulses that last longer than one CPU clock period will generate an interrupt. Shorter pulses are not guaranteed to generate an interrupt. If low-level interrupt is selected, the low level must be held until the completion of the currently executing instruction to generate an interrupt. If enabled, a level-triggered interrupt will generate an interrupt request as long as the pin is held low. Interrupt Flag Register - IFR Bit $05 Read/Write Initial Value 7 INTF1 R/W 0 6 INTF0 R/W 0 5 - R 0 4 TOV0 R/W 0 3 - R 0 2 - R 0 1 - R 0 0 - R 0 IFR * Bit 7 - INTF1: External Interrupt Flag1 When an edge on the INT1 pin triggers an interrupt request, the corresponding interrupt flag, INTF1 becomes set (one). If the I-bit in SREG and the corresponding interrupt enable bit, INT1 in GIMSK is set (one), the MCU will jump to the interrupt vector. The flag is cleared when the interrupt routine is executed. Alternatively, the flag can be cleared by writing a logical "1" to it. This flag is always cleared when INT1 is configured as level interrupt. * Bit 6 - INTF0: External Interrupt Flag0 When an edge on the INT0 pin triggers an interrupt request, the corresponding interrupt flag, INTF0 becomes set (one). If the I-bit in SREG and the corresponding interrupt enable bit, INT0 in GIMSK is set (one), the MCU will jump to the interrupt vector. The flag is cleared when the interrupt routine is executed. Alternatively, the flag can be 20 ATTINY28L/V 1062E-10/01 ATTINY28L/V cleared by writing a logical "1" to it. This flag is always cleared when INT0 is configured as level interrupt. * Bit 5 - Res: Reserved Bit This bit is a reserved bit in the ATtiny28 and always reads as zero. * Bit 4 - TOV0: Timer/Counter0 Overflow Flag The bit TOV0 is set (one) when an overflow occurs in Timer/Counter0. TOV0 is cleared by hardware when executing the corresponding interrupt handling vector. TOV0 is cleared by writing a logical "1" to the flag. When the SREG I-bit, TOIE0 in ICR and TOV0 are set (one), the Timer/Counter0 Overflow interrupt is executed. * Bit 3..0 - Res: Reserved Bits These bits are reserved bits in the ATtiny28 and always read as zero. Note: 1. One should not try to use the SBI (Set Bit in I/O Register) instruction to clear individual flags in the Register. This will result in clearing all the flags in the register, because the register is first read, then modified and finally written, thus writing ones to all set flags. Using the CBI (Clear Bit in I/O Register) instruction on IFR will result in clearing all bits apart from the specified bit. External Interrupt The external interrupt is triggered by the INT pins. Observe that, if enabled, the interrupt will trigger even if the INT pin is configured as an output. This feature provides a way of generating a software interrupt. The external interrupt can be triggered by a falling or rising edge, a pin change or a low level. This is set up as indicated in the specification for the Interrupt Control Register (ICR). When the external interrupt is enabled and is configured as level-triggered, the interrupt will trigger as long as the pin is held low. The external interrupt is set up as described in the specification for the Interrupt Control Register (ICR). Low-level Input Interrupt The low-level interrupt is triggered by setting any of the Port B pins low. However, if any Port B pins are used for other special features, these pins will not trigger the interrupt. For example, if the analog comparator is enabled, a low level on PB0 or PB1 will not cause an interrupt. This is also the case for the special functions T0, INT0 and INT1. If low-level interrupt is selected, the low level must be held until the completion of the currently executing instruction to generate an interrupt. When this interrupt is enabled, the interrupt will trigger as long as any of the Port B pins are held low. To enter the sleep modes, the SE bit in MCUCS must be set (one) and a SLEEP instruction must be executed. The SM bit in the MCUCS register selects which sleep mode (Idle or Power-down) will be activated by the SLEEP instruction. If an enabled interrupt occurs while the MCU is in a sleep mode, the MCU awakes. The CPU is then halted for four cycles. It executes the interrupt routine and resumes execution from the instruction following SLEEP. The contents of the register file and I/O memory are unaltered. If a reset occurs during sleep mode, the MCU wakes up and executes from the Reset vector. When the SM bit is cleared (zero), the SLEEP instruction forces the MCU into the Idle Mode, stopping the CPU but allowing Timer/Counters, Watchdog and the interrupt system to continue operating. This enables the MCU to wake up from external triggered interrupts as well as internal ones like Timer Overflow interrupt and Watchdog reset. If wake-up from the Analog Comparator Interrupt is not required, the analog comparator can be powered down by setting the ACD bit in the Analog Comparator Control and Status register (ACSR). This will reduce power consumption in Idle Mode. Note that the ACD bit is set by default. Sleep Modes Idle Mode 21 1062E-10/01 Power-down Mode When the SM bit is set (one), the SLEEP instruction forces the MCU into the Powerdown mode. In this mode, the external oscillator is stopped, while the external interrupts and the Watchdog (if enabled) continue operating. Only an external reset, a Watchdog reset (if enabled), or an external level interrupt can wake up the MCU. Note that if a level-triggered interrupt is used for wake-up from Power-down mode, the changed level must be held for some time to wake up the MCU. This makes the MCU less sensitive to noise. The wake-up period is equal to the clock-counting part of the reset period (see Table 5). The MCU will wake up from power-down if the input has the required level for two Watchdog oscillator cycles. If the wake-up period is shorter than two Watchdog oscillator cycles, the MCU will wake up if the input has the required level for the duration of the wake-up period. If the wake-up condition disappears before the wake-up period has expired, the MCU will wake up from power-down without executing the corresponding interrupt. The period of the Watchdog oscillator is 2.7 s (nominal) at 3.0V and 25C. The frequency of the watchdog oscillator is voltage-dependent as shown in the section "Typical Characteristics" on page 55. When waking up from the Power-down mode, there is a delay from the wake-up condition until the wake-up becomes effective. This allows the clock to restart and become stable after having been stopped. 22 ATTINY28L/V 1062E-10/01 ATTINY28L/V Timer/Counter0 The ATtiny28 provides one general-purpose 8-bit Timer/Counter - Timer/Counter0. Timer/Counter0 has prescaling selection from the 10-bit prescaling timer. The Timer/Counter0 can either be used as a timer with an internal clock time base or as a counter with an external pin connection that triggers the counting. Figure 20 shows the Timer/Counter prescaler. Figure 20. Timer/Counter0 Prescaler CK 10-BIT T/C PRESCALER CK/1024 CK/256 CK/64 Timer/Counter Prescaler COUNT ENABLE FROM MODULATOR T0 0 CS00 CS01 CS02 TIMER/COUNTER0 CLOCK SOURCE TCK0 The four different prescaled selections are: the hardware modulator period, CK/64, CK/256 and CK/1028, where CK is the oscillator clock. CK, external source and stop can also be selected as clock sources. Figure 21 shows the block diagram for Timer/Counter0. Figure 21. Timer/Counter0 Block Diagram T/C0 OVERFLOW IRQ TOIE0 INTERRUPT CONTROL REGISTER (ICR) INTERRUPT FLAG REGISTER (IFR) TOV0 TOV0 T/C0 CONTROL REGISTER (TCCR0) TIMER/COUNTER0 (TCNT0) CONTROL LOGIC T0 23 1062E-10/01 The 8-bit Timer/Counter0 can select clock source from CK, prescaled CK or an external pin. In addition, it can be stopped as described in the specification for the Timer/Counter0 Control Register (TCCR0). The overflow status flag is found in the Interrupt Flag Register (IFR). Control signals are found in the Timer/Counter0 Control Register (TCCR0). The interrupt enable/disable setting for Timer/Counter0 is found in the Interrupt Control Register (ICR). When Timer/Counter0 is externally clocked, the external signal is synchronized with the oscillator frequency of the CPU. To ensure proper sampling of the external clock, the minimum time between two external clock transitions must be at least one internal CPU clock period. The external clock signal is sampled on the rising edge of the internal CPU clock. The 8-bit Timer/Counter0 features both a high-resolution and a high-accuracy usage with the lower prescaling opportunities. Similarly, the high prescaling opportunities make the Timer/Counter0 useful for lower speed functions or exact timing functions with infrequent actions. Timer/Counter0 Control Register - TCCR0 Bit $04 Read/Write Initial Value 7 FOV0 R/W 0 6 - R 0 5 - R 0 4 OOM01 R/W 0 3 OOM00 R/W 0 2 CS02 R/W 0 1 CS01 R/W 0 0 CS00 R/W 0 TCCR0 * Bit 7 - FOV0: Force Overflow Writing a logical "1" to this bit forces a change on the overflow output pin PA2 according to the values already set in OOM01 and OOM00. If the OOM01 and OOM00 bits are written in the same cycle as FOV0, the new settings will not take effect until the next overflow or forced overflow occurs. The Force Overflow bit can be used to change the output pin without waiting for an overflow in the timer. The automatic action programmed in OOM01 and OOM00 happens as if an overflow had occurred, but no interrupt is generated. The FOV0 bit will always read as zero, and writing a zero to this bit has no effect. * Bits 6, 5 - Res: Reserved Bits These bits are reserved bits in the ATtiny28 and always read as zero. * Bits 4, 3 - OOM01, OOM00: Overflow Output Mode, Bits 1 and 0 The OOM01 and OOM00 control bits determine any output pin action following an overflow or a forced overflow in Timer/Counter0. Any output pin actions affect pin PA2. The control configuration is shown in Table 9. Table 9. Overflow Output Mode Select OOM01 0 0 1 1 OOM00 0 1 0 1 Description Timer/Counter0 disconnected from output pin PA2 Toggle the PA2 output line. Clear the PA2 output line to zero. Set the PA2 output line to one. * Bits 2, 1, 0 - CS02, CS01, CS00: Clock Select0, Bits 2, 1 and 0 The Clock Select0 bits 2, 1 and 0 define the prescaling source of Timer/Counter0. 24 ATTINY28L/V 1062E-10/01 ATTINY28L/V Table 10. Clock 0 Prescale Select CS02 0 0 0 0 1 1 1 1 CS01 0 0 1 1 0 0 1 1 CS00 0 1 0 1 0 1 0 1 Description Stop, the Timer/Counter0 is stopped. CK Modulator Period CK/64 CK/256 CK/1024 External Pin T0, falling edge External Pin T0, rising edge The Stop condition provides a Timer Enable/Disable function. The CK down divided modes are scaled directly from the CK oscillator clock. If the external pin modes are used for Timer/Counter0, transitions on PB2/(T0) will clock the counter even if the pin is configured as an output. This feature can give the user software control of the counting. Timer Counter 0 - TCNT0 Bit $03 Read/Write Initial Value 7 MSB R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 6 5 4 3 2 1 0 LSB R/W 0 TCNT0 The Timer/Counter0 is realized as an up-counter with read and write access. If the Timer/Counter0 is written and a clock source is present, the Timer/Counter0 continues counting in the timer clock cycle following the write operation. 25 1062E-10/01 Watchdog Timer The Watchdog Timer is clocked from a separate on-chip oscillator. By controlling the Watchdog Timer prescaler, the Watchdog reset interval can be adjusted as shown in Table 11. See characterization data for typical values at other VCC levels. The WDR (Watchdog Reset) instruction resets the Watchdog Timer. Eight different clock cycle periods can be selected to determine the reset period. If the reset period expires without another Watchdog reset, the ATtiny28 resets and executes from the reset vector. For timing details on the Watchdog reset, refer to page 17. To prevent unintentional disabling of the Watchdog, a special turn-off sequence must be followed when the Watchdog is disabled. Refer to the description of the Watchdog Timer Control Register for details. Figure 22. Watchdog Timer Oscillator 1 MHz at VCC = 5V 350 kHz at VCC = 3V 110 kHz at VCC = 2V Watchdog Timer Control Register - WDTCR Bit $01 Read/Write Initial Value 7 - R 0 6 - R 0 5 - R 0 4 WDTOE R/W 0 3 WDE R/W 0 2 WDP2 R/W 0 1 WDP1 R/W 0 0 WDP0 R/W 0 WDTCR * Bits 7..5 - Res: Reserved Bits These bits are reserved bits in the ATtiny28 and will always read as zero. * Bit 4 - WDTOE: Watchdog Turn-off Enable This bit must be set (one) when the WDE bit is cleared. Otherwise, the Watchdog will not be disabled. Once set, hardware will clear this bit to zero after four clock cycles. Refer to the description of the WDE bit for a Watchdog disable procedure. * Bit 3 - WDE: Watchdog Enable When the WDE is set (one), the Watchdog Timer is enabled and if the WDE is cleared (zero), the Watchdog Timer function is disabled. WDE can only be cleared if the WDTOE bit is set (one). To disable an enabled Watchdog Timer, the following procedure must be followed: 1. In the same operation, write a logical "1" to WDTOE and WDE. A logical "1" must be written to WDE even though it is set to one before the disable operation starts. 2. Within the next four clock cycles, write a logical "0" to WDE. This disables the Watchdog. 26 ATTINY28L/V 1062E-10/01 ATTINY28L/V * Bits 2..0 - WDP2, WDP1, WDP0: Watchdog Timer Prescaler 2, 1 and 0 The WDP2, WDP1 and WDP0 bits determine the Watchdog Timer prescaling when the Watchdog Timer is enabled. The different prescaling values and their corresponding time-out periods are shown in Table 11. Table 11. Watchdog Timer Prescale Select Number of WDT Oscillator Cycles 16K cycles 32K cycles 64K cycles 128K cycles 256K cycles 512K cycles 1,024K cycles 2,048K cycles Typical Time-out at VCC = 2.0V 0.15 s 0.30 s 0.60 s 1.2 s 2.4 s 4.8 s 9.6 s 19 s Typical Time-out at VCC = 3.0V 47 ms 94 ms 0.19 s 0.38 s 0.75 s 1.5 s 3.0 s 6.0 s Typical Time-out at VCC = 5.0V 15 ms 30 ms 60 ms 0.12 s 0.24 s 0.49 s 0.97 s 1.9 s WDP2 0 0 0 0 1 1 1 1 Note: WDP1 0 0 1 1 0 0 1 1 WDP0 0 1 0 1 0 1 0 1 The frequency of the Watchdog oscillator is voltage-dependent, as shown in the section "Typical Characteristics" on page 55. The WDR (Watchdog Reset) instruction should always be executed before the Watchdog Timer is enabled. This ensures that the reset period will be in accordance with the Watchdog Timer prescale settings. If the Watchdog Timer is enabled without reset, the Watchdog Timer may not start counting from zero. 27 1062E-10/01 Calibrated Internal RC Oscillator The calibrated internal oscillator provides a fixed 1.2 MHz (nominal) clock at 3V and 25C. This clock may be used as the system clock. See the section "Clock Options" on page 4 for information on how to select this clock as the system clock. This oscillator can be calibrated by writing the calibration byte to the OSCCAL register. When this oscillator is used as the chip clock, the Watchdog oscillator will still be used for the Watchdog Timer and for the reset time-out. For details on how to use the pre-programmed calibration value, see the section "Calibration Byte" on page 44. Oscillator Calibration Register - OSCCAL Bit $00 Read/Write Initial Value 7 CAL7 R/W 0 6 CAL6 R/W 0 5 CAL5 R/W 0 4 CAL4 R/W 0 3 CAL3 R/W 0 2 CAL2 R/W 0 1 CAL1 R/W 0 0 CAL0 R/W 0 OSCCAL * Bits 7..0 - CAL7..CAL0: Oscillator Calibration Value Writing the calibration byte to this address will trim the internal oscillator to remove process variation from the oscillator frequency. When OSCCAL is zero, the lowest available frequency is chosen. Writing non-zero values to the register will increase the frequency to the internal oscillator. Writing $FF to the register gives the highest available frequency. Table 12 shows the range for OSCCAL. Note that the oscillator is intended for calibration to 1.2 MHz, thus tuning to other values is not guaranteed. At 3V and 25oC, the pre-programmed calibration byte gives a frequency within 1% of the nominal frequency. Table 12. Internal RC Oscillator Range OSCCAL Value 0x00 0x7F 0xFF Min Frequency 0.6 MHz 0.8 MHz 1.2 MHz Max Frequency 1.2 MHz 1.7 MHz 2.5 MHz 28 ATTINY28L/V 1062E-10/01 ATTINY28L/V Hardware Modulator ATtiny28 features a built-in hardware modulator connected to a high-current output pad, PA2. The hardware modulator generates a configurable pulse train. The on-time of a pulse can be set to a number of chip clock cycles. This is done by configuring the Modulation Control Register (MODCR). Modulation Control Register - MODCR Bit $02 Read/Write Initial Value 7 ONTIM4 6 ONTIM3 5 ONTIM2 4 ONTIM1 3 ONTIM0 2 MCONF2 1 MCONF1 0 MCONF0 MODCR R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 * Bits 7..3 - ONTIM4..0: Modulation On-time This 5-bit value +1 determines the number of clock cycles the output pin PA2 is active (low). * Bits 2..0 - MCONF2..0: Modulation Configuration Bits 2, 1 and 0 These three bits determine the relationship between the on- and off-times of the modulator, and thereby the duty-cycle. The various settings are shown in Table 13. The minimum and maximum modulation period is also shown in the table. The minimum modulation period is obtained by setting ONTIM to zero, while the maximum period is obtained by setting ONTIM to 31. The configuration values for some common oscillator and carrier frequencies are listed in Table 15. The relationship between oscillator frequency and carrier frequency is: fosc fcarrier = ----------------------------------------------------( On-time + Off-time ) If the MCONF register is set to 111, the carrier frequency will be equal to the oscillator frequency. Table 13. MCONF2..0 Effect on Duty-cycle and Modulation Period MCONF2..0 000 001 010 011 100 101 110 111 Note: On-time X ONTIM+1 ONTIM+1 ONTIM+1 2 x (ONTIM+1) 3 x (ONTIM+1) Off-time X ONTIM+1 2 x (ONTIM+1) 3 x (ONTIM+1) ONTIM+1 ONTIM+1 Duty-cycle 100% 50% 33% 25% 67% 75% Min Period X 2 CK 3 CK 4 CK 3 CK 4 CK Reserved X X Note 1 1 CK 1 CK High-frequency output In the high-frequency mode, the output is gated with the clock signal. Thus, the on- and off-times will be dependent on the clock input to the MCU. Also note that when changing from this mode directly to another modulation mode, the output will have a small glitch. Thus, PA2 should be set to stop the modulated output before changing from this mode. Max Period X 64 CK 96 CK 128 CK 96 CK 128 CK Comment Unmodulated output 29 1062E-10/01 PA2 is the built-in, high-current LED driver and it is always an output pin. The output buffer can sink 25 mA at VCC = 2.0V. When MCONF is zero, modulation is switched off and the pin acts as a normal high-current output pin. The following truth table shows the effect of various PORTA2 and MCONF settings. Table 14. PA2 Output PORTA2 0 0 1 MCONF 0 1-7 X PA2 Output 0 Modulated 1 The modulation period is available as a prescale to Timer/Counter0 and thus, this timer should be used to time the length of each burst. If the number of pulses to be sent is N, the number 255 - N should be loaded to the timer. When an overflow occurs, the transmission is complete.The OOM01 and OOM00 bits in TCCR0 can be configured to automatically change the value on PA2 when a Timer/Counter0 overflow occurs. See "Timer/Counter0" on page 23 for details on how to configure the OOM01 and OOM00 bits. The modulation period is available as a prescale even when PORTA2 is high and modulation is stopped. Thus, this prescale can also be used to time the intervals between bursts. To get a glitch-free output, the user should first configure the MODCR register to enable modulation. There are two ways to start the modulation: 1. Clear the PORTA2 bit in Port A Data Register (PORTA). 2. Configure OOM00 and OOM01 bits in the Timer/Counter0 Control Register (TCCR0) to clear PA2 on the next overflow. Either an overflow or a forced overflow can then be used to start modulation. The PA2 output will then be set low at the start of the next cycle. To stop the modulated output, the user should set the PORTA2 bit or configure OOM00 and OOM01 to set PA2 on the next overflow. If the MODCR register is changed during modulation, the changed value will take effect at the start of the next cycle, producing a glitch-free output. See Figure 23 below and Figure 30 on page 38. 30 ATTINY28L/V 1062E-10/01 ATTINY28L/V Figure 23. The Hardware Modulator RM 8 / 5 ONTIM 5 / IONTIM / 5 / MODULATOR STATE MACHINE 3 / 3 IMCONF MCONF / 3/ COUNT ENABLE TO TIMER/COUNTER0 WM IPORTA2 FROM PORTA2 DISABLE MODUALTOR ENABLE SETTING WM: WRITE MODCR RM: READ MODCR D Q 0 1 PA2 Figure 24 to Figure 27 show examples on output from the Modulator. Figure 24 also shows the timing for the enable setting signal and for the count enable signal to Timer/Counter0. Figure 24. Modulation with ONTIM = 3, MCONF = 010. CLK PA2 ENABLE SETTING COUNT ENABLE Note: 1. Clock frequency: 455 kHz; modulation frequency: 38 kHz; duty-cycle: 33% Figure 25. Modulation with ONTIM = 5, MCONF = 001 CLK PA2 Note: Clock frequency: 455 kHz; modulation frequency: 38 kHz; duty-cycle: 50% 31 1062E-10/01 Figure 26. Modulation with ONTIM = 1, MCONF = 011 CLK PA2 Note: Clock frequency: 3.64 MHz; modulation frequency: 455 kHz; duty-cycle: 25% Figure 27. Modulation with ONTIM = 3, MCONF = 001 CLK PA2 Note: Clock frequency: 3.64 MHz; modulation frequency: 455 kHz; duty-cycle: 50% Table 15. Some Common Modulator Configurations Crystal/Resonator Frequency 455 kHz 455 kHz 455 kHz 455 kHz 455 kHz 1 MHz 1.8432 MHz 1.8432 MHz 1.8432 MHz 2 MHz 2 MHz 2.4576 MHz 3.2768 MHz 4 MHz 455 kHz 1 MHz 1.82 MHz 1.82 MHz 1.8432 MHz 1.8432 MHz 2 MHz 2 MHz Carrier Frequency 38 kHz 38 kHz 38 kHz 38 kHz 38 kHz 38 kHz 38 kHz 38 kHz 38 kHz 38 kHz 38 kHz 38 kHz 38 kHz 38 kHz 455 kHz 455 kHz 455 kHz 455 kHz 455 kHz 455 kHz 455 kHz 455 kHz % Error in Frequency 0.2 0.2 0.2 0.2 0.2 1.2 1.1 1.1 1.1 1.2 1.2 1.1 2.0 1.2 0.0 9.9 0.0 0.0 1.3 1.3 9.9 9.9 Duty-cycle 25% 33% 50% 67% 75% 50% 25% 33% 50% 25% 50% 50% 25% 25% approx. 50% 50% 25% 50% 25% 50% 25% 50% ONTIM Value 2 3 5 3 2 12 11 15 23 12 25 31 21 25 X 0 0 1 0 1 0 1 MCONF Value 011 010 001 100 101 001 011 010 001 011 001 001 011 011 111 001 011 001 011 001 011 001 32 ATTINY28L/V 1062E-10/01 ATTINY28L/V Table 15. Some Common Modulator Configurations (Continued) Crystal/Resonator Frequency 2.4576 MHz 2.4576 MHz 3.2768 MHz 3.2768 MHz 3.64 MHz 3.64 MHz 4 MHz 4 MHz Carrier Frequency 455 kHz 455 kHz 455 kHz 455 kHz 455 kHz 455 kHz 455 kHz 455 kHz % Error in Frequency 10.0 10.0 10.0 10.0 0.0 0.0 9.9 9.9 Duty-cycle 33% 50% 25% 50% 25% 50% 25% 50% ONTIM Value 1 2 1 3 1 3 1 3 MCONF Value 010 001 011 001 011 001 011 001 33 1062E-10/01 Analog Comparator The analog comparator compares the input values on the positive input PB0 (AIN0) and negative input PB1 (AIN1). When the voltage on the positive input PB0 (AIN0) is higher than the voltage on the negative input PB1 (AIN1), the Analog Comparator Output (ACO) is set (one). The comparator can trigger a separate interrupt exclusive to the analog comparator. The user can select interrupt triggering on comparator output rise, fall or toggle. A block diagram of the comparator and its surrounding logic is shown in Figure 28. Figure 28. Analog Comparator Block Diagram PB0 PB1 Analog Comparator Control and Status Register - ACSR Bit $08 Read/Write Initial Value 7 ACD R/W 1 6 - R 0 5 ACO R X 4 ACI R/W 0 3 ACIE R/W 0 2 - R 0 1 ACIS1 R/W 0 0 ACIS0 R/W 0 ACSR * Bit 7 - ACD: Analog Comparator Disable When this bit is set (one), the power to the analog comparator is switched off. This bit can be set at any time to turn off the analog comparator. When changing the ACD bit, the Analog Comparator Interrupt must be disabled by clearing the ACIE bit in ACSR. Otherwise, an interrupt can occur when the bit is changed. To use the analog comparator, the user must clear this bit. * Bit 6 - Res: Reserved Bit This bit is a reserved bit in the ATtiny28 and will always read as zero. * Bit 5 - ACO: Analog Comparator Output ACO is directly connected to the comparator output. * Bit 4 - ACI: Analog Comparator Interrupt Flag This bit is set (one) when a comparator output event triggers the interrupt mode defined by ACI1 and ACI0. The Analog Comparator Interrupt routine is executed if the ACIE bit is set (one) and the I-bit in SREG is set (one). ACI is cleared by hardware when executing the corresponding interrupt handling vector. Alternatively, ACI is cleared by writing a logical "1" to the flag. * Bit 3 - ACIE: Analog Comparator Interrupt Enable When the ACIE bit is set (one) and the I-bit in the Status Register is set (one), the analog comparator interrupt is activated. When cleared (zero), the interrupt is disabled. 34 ATTINY28L/V 1062E-10/01 ATTINY28L/V * Bit 2 - RES: Reserved Bit This bit is a reserved bit in the ATtiny28 and will always read as zero. * Bits 1, 0 - ACIS1, ACIS0: Analog Comparator Interrupt Mode Select These bits determine which comparator events trigger the Analog Comparator Interrupt. The different settings are shown in Table 16. Table 16. ACIS1/ACIS0 Settings ACIS1 0 0 1 1 Note: ACIS0 0 1 0 1 Interrupt Mode Comparator Interrupt on Output Toggle Reserved Comparator Interrupt on Falling Output Edge Comparator Interrupt on Rising Output Edge When changing the ACIS1/ACIS0 bits, the Analog Comparator Interrupt must be disabled by clearing its Interrupt Enable bit in the ACSR register. Otherwise, an interrupt can occur when the bits are changed. Caution: Using the SBI or CBI instruction on bits other than ACI in this register will write a one back into ACI if it is read as set, thus clearing the flag. 35 1062E-10/01 I/O Ports All AVR ports have true read-modify-write functionality when used as general digital I/O ports. This means that the direction of one port pin can be changed without unintentionally changing the direction of any other pin with the SBI and CBI instructions. The same applies for changing drive value (if configured as output) or enabling/disabling of pull-up resistors (if configured as input). Port A is a 4-bit I/O port. PA2 is output-only, while PA3, PA1 and PA0 are bi-directional. Three I/O memory address locations are allocated for Port A, one each for the Data Register - PORTA, $1B, Port A Control Register - PACR, $1A and the Port A Input Pins - PINA, $19. The Port A Input Pins address is read-only, while the Data Register and the Control Register are read/write. Compared to other output ports, the Port A output is delayed one extra clock cycle. Port pins PA0, PA1 and PA3 have individually selectable pull-up resistors. When pins PA0, PA1 or PA3 are used as inputs and are externally pulled low, they will source current if the internal pull-up resistors are activated. PA2 is output-only. The PA2 output buffer can sink 25 mA and thus drive a high-current LED directly. This output can also be modulated (see "Hardware Modulator" on page 29 for details). Port A Port A Data Register - PORTA Bit $1B Read/Write Initial Value 7 - 6 - 5 - 4 - 3 PORTA3 2 PORTA2 1 PORTA1 0 PORTA0 PORTA R 0 R 0 R 0 R 0 R/W 0 R/W 1 R/W 0 R/W 0 Port A Control Register - PACR Bit $1A Read/Write Initial Value 7 - R 0 6 - R 0 5 - R 0 4 - R 0 3 DDA3 R/W 0 2 PA2HC R/W 0 1 DDA1 R/W 0 0 DDA0 R/W 0 PACR * Bits 7..4 - Res: Reserved Bits These bits are reserved bits in the ATtiny28 and always read as zero. * Bit 3 - DDA3: Data Direction PA3 When DDA3 is set (one), the corresponding pin is an output pin. Otherwise, it is an input pin. * Bit 2 - PA2HC: PORTA2 High Current Enable When the PA2HC bit is set (one), an additional driver at the output pin PA2 is enabled. This makes it possible to sink 25 mA at VCC = 1.8V (VOL = 0.8V). When the PA2HC bit is cleared (zero), PA2 can sink 15 mA at VCC = 1.8V (VOL = 0.8V). * Bits 1, 0 - DDA1, DDA0: Data Direction PA1 and PA0 When DDAn is set (one), the corresponding pin is an output pin. Otherwise, it is an input pin. 36 ATTINY28L/V 1062E-10/01 ATTINY28L/V Port A as General Digital I/O PA3, PA1 and PA0 are general I/O pins. The DDAn (n: 3,1,0) bits in PACR select the direction of these pins. If DDAn is set (one), PAn is configured as an output pin. If DDAn is cleared (zero), PAn is configured as an input pin. If PORTAn is set (one) when the pin is configured as an input pin, the MOS pull-up resistor is activated. To switch the pull-up resistor off, the PORTAn bit has to be cleared (zero) or the pin has to be configured as an output pin. The effects of the DDAn and PORTAn bits on PA3, PA1 and PA0 are shown in Table 17. The port pins are tri-stated when a reset condition becomes active, even if the clock is not running. Table 17. DDAn Effects on Port A Pins DDAn 0 0 1 1 Note: PORTAn 0 1 0 1 I/O Input Input Output Output Pull-up No Yes No No Comment Tri-state (high-Z) PAn will source current if ext. pulled low. Push-pull Zero Output Push-pull One Output n: 3,1,0, pin number Port A Input Pins Address - PINA Bit $19 Read/Write Initial Value 7 - R 0 6 - R 0 5 - R 0 4 - R 0 3 PINA3 R N/A 2 - R 0 1 PINA1 R N/A 0 PINA0 R N/A PINA The Port A Input Pins address (PINA) is not a register; this address enables access to the physical value on each Port A pin. When reading PORTA, the Port A Data Latch is read and when reading PINA, the logical values present on the pins are read. Alternate Function of PA2 PA2 is the built-in, high-current LED driver and it is always an output pin. The output signal can be modulated with a software programmable frequency. See "Hardware Modulator" on page 29 for further details. 37 1062E-10/01 Port A Schematics Note that all port pins are synchronized. The synchronization latches are, however, not shown in the figures. Figure 29. Port A Schematic Diagram (Pins PA0, PA1 and PA3) RD MOS PULLUP RESET Q R DDAn C D WD RESET RESET PAn Q R C D R D Q PORTAn C RL WP RP WP: WD: RL: RP: RD: n: WRITE PORTA WRITE DDRA READ PORTA LATCH READ PORTA PIN READ DDRA 0,1,3 Figure 30. Port A Schematic Diagram (Pin PA2) RESET R Q D PORTA2 C PA2 HARDWARE MODULATOR 1 0 WP RL DISABLE TOGGLE RESET WP: WRITE PORTA RL: READ PORTA LATCH Note: Both the flip-flops shown have reset value one (set). OOM01 OOM00 0 0 0 1 CLEAR 1 0 SET 1 1 Q R D C TOV0 FOV0 38 ATTINY28L/V 1062E-10/01 DATA BUS DATA BUS ATTINY28L/V Port B Port B is an 8-bit input port. One I/O address location is allocated for the Port B Input Pins - PINB, $16. The Port B Input Pins address is read-only. All port pins have pull-ups that can be switched on for all Port B pins simultaneously. If any of the Port B special functions is enabled, the corresponding pull-up(s) is disabled. When pins PB0 to PB7 are externally pulled low, they will source current (IIL) if the internal pull-up resistors are activated. The Port B pins with alternate functions are shown in Table 18. Table 18. Port B Pin Alternate Functions Port Pin PB0 PB1 PB2 PB3 PB4 Alternate Functions AIN0 (Analog Comparator Positive Input) AIN1 (Analog Comparator Negative Input) T0 (Timer/Counter 0 External Counter Input) INT0 (External Interrupt 0 Input) INT1 (External Interrupt 1 Input) Port B Input Pins Address - PINB Bit $16 Read/Write Initial Value 7 PINB7 R N/A 6 PINB6 R N/A 5 PINB5 R N/A 4 PINB4 R N/A 3 PINB3 R N/A 2 PINB2 R N/A 1 PINB1 R N/A 0 PINB0 R N/A PINB The Port B Input Pins address (PINB) is not a register; this address enables access to the physical value on each Port B pin. When reading PINB, the logical values present on the pins are read. Port B as General Digital Input All eight pins in Port B have equal functionality when used as digital input pins. PBn, general input pin: To switch the pull-up resistors on, the PLUPB bit in the MCUCS register must be set (one). This bit controls the pull-up on all Port B pins. To turn the pull-ups off, this bit has to be cleared (zero). Note that if any Port B pins are used for alternate functions, the pull-up on the corresponding pins are disabled. The port pins are tri-stated when a reset condition becomes active, even if the clock is not running. Alternate Functions of Port B All Port B pins are connected to a low-level detector that can trigger the low-level input interrupt. See "Low-level Input Interrupt" on page 21 for details. In addition, Port B has the following alternate functions: * INT1 - Port B, Bit 4 INT1, External Interrupt source 1. The PB4 pin can serve as an external interrupt source to the MCU. See the interrupt description for details on how to enable and configure this interrupt. If the interrupt is enabled, the pull-up resistor on PB4 is disabled and PB4 will not give low-level interrupts. * INT0 - Port B, Bit 3 INT0, External Interrupt source 0. The PB3 pin can serve as an external interrupt source to the MCU. See the interrupt description for details on how to enable and configure this interrupt. If the interrupt is enabled, the pull-up resistor on PB3 is disabled and PB3 will not give low-level interrupts. 39 1062E-10/01 * T0 - Port B, Bit 2 T0, Timer/Counter0 Counter source. See the timer description for further details. If T0 is used as the counter source, the pull-up resistor on PB2 is disabled and PB2 will not give low-level interrupts. * AIN1 - Port B, Bit 1 AIN1, Analog Comparator Negative input. When the on-chip analog comparator is enabled, this pin also serves as the negative input of the comparator. If the analog comparator is enabled, the pull-up resistors on PB1 and PB0 are disabled and these pins will not give low-level interrupts. * AIN0 - Port B, Bit 0 AIN0, Analog Comparator Positive input. When the on-chip analog comparator is enabled, this pin also serves as the positive input of the comparator. If the analog comparator is enabled, the pull-up resistors on PB1 and PB0 are disabled and these pins will not give low-level interrupts. Port B Schematics Note that all port pins are synchronized. The synchronization latches are, however, not shown in the figures. Figure 31. Port B Schematic Diagram (Pins PB0 and PB1) MOS PULLUP PULL-UP PORT B COMPARATOR DISABLE PWRDN RP PBn TO LOW-LEVEL DETECTOR TO COMPARATOR AINn RP: READ PORTB PIN n : 0, 1 40 ATTINY28L/V 1062E-10/01 DATA BUS ATTINY28L/V Figure 32. Port B Schematic Diagram (Pin PB2) MOS PULLUP PULL-UP PORT B RP PB2 TO LOW-LEVEL DETECTOR SENSE CONTROL TIMER0 CLOCK SOURCE MUX CS02 CS01 CS00 RP: READ PORTB PIN Figure 33. PORT B Schematic Diagram (Pins PB3 and PB4) PULL-UP PORT B INTm ENABLE MOS PULLUP RP PBn TO LOW-LEVEL DETECTOR SENSE CONTROL INTm ISCm1 ISCm0 RP: READ PORTB PIN n : 3, 4 m : 0, 1 DATA BUS DATA BUS 41 1062E-10/01 Figure 34. PORT B Schematic Diagram (Pins PB7 - PB5) MOS PULLUP PULL-UP PORT B RP PBn TO LOW-LEVEL DETECTOR RP: n: READ PORT B PIN 5-7 Port D Port D is an 8-bit bi-directional I/O port with internal pull-up resistors. Three I/O memory address locations are allocated for Port D, one each for the Data Register - PORTD, $12, Data Direction Register - DDRD, $11 and the Port D Input Pins - PIND, $10. The Port D Input Pins address is read-only, while the Data Register and the Data Direction Register are read/write. The Port D output buffers can sink 10 mA. As inputs, Port D pins that are externally pulled low will source current if the pull-up resistors are activated. Port D Data Register - PORTD Bit $12 Read/Write Initial Value 7 PORTD7 6 PORTD6 5 PORTD5 4 PORTD4 3 PORTD3 2 PORTD2 1 PORTD1 0 PORTD0 PORTD R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 Port D Data Direction Register - DDRD Bit $11 Read/Write Initial Value 7 DDD7 R/W 0 6 DDD6 R/W 0 5 DDD5 R/W 0 4 DDD4 R/W 0 3 DDD3 R/W 0 2 DDD2 R/W 0 1 DDD1 R/W 0 0 DDD0 R/W 0 DDRD Port D Input Pins Address - PIND Bit $10 Read/Write Initial Value 7 PIND7 R N/A 6 PIND6 R N/A 5 PIND5 R N/A 4 PIND4 R N/A 3 PIND3 R N/A 2 PIND2 R N/A 1 PIND1 R N/A 0 PIND0 R N/A PIND The Port D Input Pins Address (PIND) is not a register; this address enables access to the physical value on each Port D pin. When reading PORTD, the Port D Data Latch is read and when reading PIND, the logical values present on the pins are read. 42 ATTINY28L/V 1062E-10/01 DATA BUS ATTINY28L/V Port D as General Digital I/O All eight pins in Port D have equal functionality when used as digital I/O pins. PDn, general I/O pin: The DDDn bit in the DDRD register selects the direction of this pin. If DDDn is set (one), PDn is configured as an output pin. If DDDn is cleared (zero), PDn is configured as an input pin. If PDn is set (one) when configured as an input pin, the MOS pull-up resistor is activated. To switch the pull-up resistor off, the PDn has to be cleared (zero), or the pin has to be configured as an output pin. The port pins are tristated when a reset condition becomes active, even if the clock is not running. Table 19. DDDn Bits on Port D Pins DDDn 0 0 1 1 Note: PORTDn 0 1 0 1 I/O Input Input Output Output Pull-up No Yes No NO Comment Tri-state (high-Z) PDn will source current if ext. pulled low Push-pull Zero Output Push-pull One Output n: 7,6,...,0, pin number Figure 35. Port D Schematic Diagram (Pins PD7 - PD0) RD MOS PULLUP RESET R Q D DDDn C WD RESET R Q D PORTDn C RL PDn WP RP WP: WD: RL: RP: RD: n: WRITE PORTD WRITE DDRD READ PORTD LATCH READ PORTD PIN READ DDRD 0-7 DATA BUS 43 1062E-10/01 Memory Programming Program Memory Lock Bits The ATtiny28 MCU provides two Lock bits that can be left unprogrammed ("1") or can be programmed ("0") to obtain the additional features listed in Table 20. The Lock bits can only be erased with the Chip Erase command. Table 20. Lock Bit Protection Modes Memory Lock Bits Mode 1 2 3 Note: LB1 1 0 0 LB2 1 1 0 Protection Type No memory lock features enabled. Further programming of the Flash is disabled.(1) Same as mode 2, and verify is also disabled. 1. Further programming of the Fuse bits is also disabled. Program the Fuse bits before programming the Lock bits. Fuse Bits The ATtiny28 has five Fuse bits, INTCAP and CKSEL3..0. * When the INTCAP Fuse is programmed ("0"), internal load capacitors are connected between XTAL1/XTAL2 and GND, similar to C1 and C2 in Figure 2. See "Crystal Oscillator" on page 4. Default value is unprogrammed ("1"). CKSEL3..0 Fuses: See Table 1, "Device Clocking Option Select," on page 4 and Table 5, "ATtiny28 Clock Options and Start-up Time," on page 14, for which combination of CKSEL3..0 to use. Default value is "0010", internal RC oscillator with long start-up time. * The status of the Fuse bits is not affected by Chip Erase. Signature Bytes All Atmel microcontrollers have a 3-byte signature code that identifies the device. The three bytes reside in a separate address space. For the ATtiny28, they are: 1. $000: $1E (indicates manufactured by Atmel) 2. $001: $91 (indicates 2 KB Flash memory) 3. $002: $07 (indicates ATtiny28 device when signature byte $001 is $91) Calibration Byte The ATtiny28 has one byte calibration value for the internal RC oscillator. This byte resides in the high byte of address $000 in the signature address space. During memory programming, the external programmer must read this location, and program it into a selected location in the the normal Flash program memory. At start-up, the user software must read this Flash location and write the value to the OSCCAL register. Atmel's ATtiny28 offers 2K bytes of Flash program memory. The ATtiny28 is shipped with the on-chip Flash program memory array in the erased state (i.e., contents = $FF) and ready to be programmed. This device supports a highvoltage (12V) parallel programming mode. Only minor currents (<1mA) are drawn from the +12V pin during programming. The program memory array in the ATtiny28 is programmed byte-by-byte. During programming, the supply voltage must be in accordance with Table 21. Programming the Flash 44 ATTINY28L/V 1062E-10/01 ATTINY28L/V Table 21. Supply Voltage during Programming Part ATtiny28 Serial Programming Not applicable Parallel Programming 4.5 - 5.5V Parallel Programming Signal Names This section describes how to parallel program and verify Flash program memory, Lock bits and Fuse bits in the ATtiny28. In this section, some pins of the ATtiny28 are referenced by signal names describing their function during parallel programming. See Figure 36 and Table 22. Pins not described in Table 22 are referenced by pin name. The XA1/XA0 pins determine the action executed when the XTAL1 pin is given a positive pulse. The coding is shown in Table 23. When pulsing WR or OE, the command loaded determines the action executed. The command is a byte where the different bits are assigned functions, as shown in Table 24. Figure 36. Parallel Programming ATtiny28 RDY/BSY OE WR BS XA0 XA1 +12V PD1 PD2 PD3 PD4 PD5 PD6 RESET VCC PB7 - PB0 DATA +5V XTAL1 GND 45 1062E-10/01 Table 22. Pin Name Mapping Signal Name in Programming Mode RDY/BSY OE WR BS XA0 XA1 DATA . Pin Name PD1 PD2 PD3 PD4 PD5 PD6 PB7 - PB0 I/O O I I I I I I/O Function "0": Device is busy programming, "1": Device is ready for new command Output Enable (active low) Write Pulse (active low) Byte Select ("0" selects low byte, "1" selects high byte) XTAL1 Action Bit 0 XTAL1 Action Bit 1 Bi-directional Data Bus (output when OE is low) Table 23. XA1 and XA0 Coding XA1 0 0 1 1 XA0 0 1 0 1 Action when XTAL1 is Pulsed Load Flash/Signature byte Address (High or low address byte for Flash determined by BS) Load Data (High or low data byte for Flash determined by BS) Load Command No Action, Idle Table 24. Command Byte Coding Command Byte 1000 0000 0100 0000 0010 0000 0001 0000 0000 1000 0000 0100 0000 0010 Command Executed Chip Erase Write Fuse Bits Write Lock Bits Write Flash Read Signature Bytes and Calibration Byte Read Fuse and Lock Bits Read Flash Enter Programming Mode The following algorithm puts the device in parallel programming mode: 1. Apply 4.5 - 5.5V between VCC and GND. 2. Set RESET and BS pins to "0" and wait at least 100 ns. 3. Apply 11.5 - 12.5V to RESET. Any activity on BS within 100 ns after +12V has been applied to RESET will cause the device to fail entering programming mode. 46 ATTINY28L/V 1062E-10/01 ATTINY28L/V Chip Erase The Chip Erase command will erase the Flash memory and the Lock bits. The Lock bits are not reset until the Flash has been completely erased. The Fuse bits are not changed. Chip Erase must be performed before the Flash is reprogrammed. Load Command "Chip Erase" 1. Set XA1, XA0 to "10". This enables command loading. 2. Set BS to "0". 3. Set DATA to "1000 0000". This is the command for Chip Erase. 4. Give XTAL1 a positive pulse. This loads the command. 5. Give WR a negative pulse. This starts the Chip Erase. RDY/BSY goes low. 6. Wait until RDY/BSY goes high before loading a new command. Programming the Flash A: Load Command "Write Flash" 1. Set XA1, XA0 to "10". This enables command loading. 2. Set BS to "0". 3. Set DATA to "0001 0000". This is the command for Write Flash. 4. Give XTAL1 a positive pulse. This loads the command. B: Load Address High Byte 1. Set XA1, XA0 to "00". This enables address loading. 2. Set BS to "1". This selects high byte. 3. Set DATA = Address high byte ($00 - $03). 4. Give XTAL1 a positive pulse. This loads the address high byte. C: Load Address Low Byte 1. Set XA1, XA0 to "00". This enables address loading. 2. Set BS to "0". This selects low byte. 3. Set DATA = Address low byte ($00 - $FF). 4. Give XTAL1 a positive pulse. This loads the address low byte. D: Load Data Low Byte 1. Set XA1, XA0 to "01". This enables data loading. 2. Set DATA = Data low byte ($00 - $FF). 3. Give XTAL1 a positive pulse. This loads the data low byte. E: Write Data Low Byte 1. Set BS to "0". This selects low data. 2. Give WR a negative pulse. This starts programming of the data byte. RDY/BSY goes low. 3. Wait until RDY/BSY goes high to program the next byte. (See Figure 37 for signal waveforms.) F: Load Data High Byte 1. Set XA1, XA0 to "01". This enables data loading. 2. Set DATA = Data high byte ($00 - $FF). 3. Give XTAL1 a positive pulse. This loads the data high byte. G: Write Data High Byte 47 1062E-10/01 1. Set BS to "1". This selects high data. 2. Give WR a negative pulse. This starts programming of the data byte. RDY/BSY goes low. 3. Wait until RDY/BSY goes high to program the next byte. (See Figure 38 for signal waveforms.) The loaded command and address are retained in the device during programming. For efficient programming, the following should be considered: * * * The command needs to be loaded only once when writing or reading multiple memory locations. Address high byte only needs to be loaded before programming a new 256-word page in the Flash. Skip writing the data value $FF, that is, the contents of the entire Flash after a Chip Erase. These considerations also apply to Flash and signature bytes reading. Reading the Flash The algorithm for reading the Flash memory is as follows (refer to "Programming the Flash" for details on command and address loading): A: Load Command "0000 0010". B: Load Address High Byte ($00 - $03). C: Load Address Low Byte ($00 - $FF). 1. Set OE to "0", and BS to "0". The Flash word low byte can now be read at DATA. 2. Set BS to "1". The Flash word high byte can now be read from DATA. 3. Set OE to "1". Programming the Fuse Bits The algorithm for programming the Fuse bits is as follows (refer to "Programming the Flash" for details on command and data loading): A: Load Command "0100 0000". D: Load Data Low Byte. Bit n = "0" programs and bit n = "1" erases the Fuse bit. Bit 4 = INTCAP Fuse Bit 3 = CKSEL3 Fuse Bit 2 = CKSEL2 Fuse Bit 1 = CKSEL1 Fuse Bit 0 = CKSEL0 Fuse Bits 7 - 5 = "1". These bits are reserved and should be left unprogrammed ("1"). E: Write Data Low Byte. Programming the Lock Bits The algorithm for programming the Lock bits is as follows (refer to "Programming the Flash" for details on command and data loading): A: Load Command "0010 0000". D: Load Data Low Byte. Bit n = "0" programs the Lock bit. Bit 2 = Lock Bit2 Bit 1 = Lock Bit1 Bits 7 - 3,0 = "1". These bits are reserved and should be left unprogrammed ("1"). E: Write Data Low Byte. The Lock bits can only be cleared by executing Chip Erase. 48 ATTINY28L/V 1062E-10/01 ATTINY28L/V Reading the Fuse and Lock Bits The algorithm for reading the Fuse and Lock bits is as follows (refer to "Programming the Flash" for details on command loading): A: Load Command "0000 0100". 1. Set OE to "0", and BS to "0". The status of the Fuse bits can now be read at DATA ("0" means programmed). Bit 4 = INTCAP Fuse Bit 3 = CKSEL3 Fuse Bit 2 = CKSEL2 Fuse Bit 1 = CKSEL1 Fuse Bit 0 = CKSEL0 Fuse 2. Set BS to "1". The status of the Lock bits can now be read at DATA ("0" means programmed). Bit 2: Lock Bit2 Bit 1: Lock Bit1 3. Set OE to "1". Reading the Signature Bytes and Calibration Byte The algorithm for reading the signature bytes and the calibration byte is as follows (refer to "Programming the Flash" for details on command and address loading): A: Load Command "0000 1000". C: Load Address Low Byte ($00 - $02). 1. Set OE to "0", and BS to "0". The selected signature byte can now be read at DATA. C: Load Address Low Byte ($00). 1. Set OE to "0", and BS to "1". The calibration byte can now be read at DATA. 2. Set OE to "1". Figure 37. Programming the Flash Waveforms DATA $10 ADDR. HIGH ADDR. LOW DATA LOW XA1 XA0 BS XTAL1 WR RDY/BSY RESET OE 12V 49 1062E-10/01 Figure 38. Programming the Flash Waveforms (Continued) DATA DATA HIGH XA1 XA0 BS XTAL1 WR RDY/BSY RESET OE +12V 50 ATTINY28L/V 1062E-10/01 ATTINY28L/V Parallel Programming Characteristics Figure 39. Parallel Programming Timing tXLWL XTAL1 tDVXH Data & Contol (DATA, XA0/1, BS) WR RDY/BSY tWLRL tWLRH tOLDV tRHBX tXHXL tXLDX tBVWL DATA Parallel Programming Characteristics TA = 25C 10%, VCC = 5V 10% Symbol VPP IPP tDVXH tXHXL tXLDX tXLWL tBVWL tRHBX tWLWH tWLRL tWLRH tXLOL tOLDV tOHDZ Parameter Programming Enable Voltage Programming Enable Current Data & Control Valid before XTAL1 High XTAL1 Pulse Width High Data & Control Hold after XTAL1 Low XTAL1 Low to WR Low BS Valid to WR Low BS Hold after RDY/BSY High WR Pulse Width Low WR Low to RDY/BSY Low WR Low to RDY/BSY High XTAL1 Low to OE Low OE Low to DATA Valid OE High to DATA Tri-stated 67.0 67.0 67.0 67.0 67.0 67.0 67.0 0.0 0.5 67.0 20.0 20.0 0.7 2.5 0.9 Min 11.5 Typ Max 12.5 250.0 Unit V A ns ns ns ns ns ns ns s ms ns ns ns 1062E-10/01 Read OE tXLOL tOHDZ Write tWLWH 51 Electrical Characteristics Absolute Maximum Ratings Operating Temperature............................. -40C to +85/105C Storage Temperature ..................................... -65C to +150C Voltage on Any Pin except RESET with Respect to Ground .............................-1.0V to VCC + 0.5V Maximum Operating Voltage ............................................ 6.0V Voltage on RESET with Respect to Ground ....-1.0V to +13.0V DC Current per I/O Pin, except PA2 ........................... 40.0 mA DC Current PA2 .......................................................... 60.0 mA DC Current VCC and GND Pin................................. 300.0 mA *NOTICE: Stresses beyond those ratings listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC Characteristics TA = -40C to 85C, VCC = 1.8V to 5.5V (unless otherwise noted) Symbol VIL VIL1 VIH VIH1 VIH2 VOL VOL VOH IIL IIL RI/O Parameter Input Low Voltage Input Low Voltage Input High Voltage Input High Voltage Input High Voltage Output Low Voltage Ports A, D (3) Condition (Except XTAL) XTAL (Except XTAL, RESET) XTAL RESET IOL = 20 mA, VCC = 5V IOL = 10 mA, VCC = 3V IOL = 25 mA, VCC = 2.0V IOH = -3 mA, VCC = 5V IOH = -1.5 mA, VCC = 3V VCC = 5.5V, pin low (absolute value) VCC = 5.5V, pin high (absolute value) Min -0.5 -0.5 0.6 VCC (2) Typ Max 0.3 Vcc 0.1 Vcc (1) (1) Units V V V V V V V V V V V VCC + 0.5 VCC + 0.5 VCC + 0.5 0.6 0.5 1.0 0.7 VCC(2) 0.85 VCC (2) Output Low Voltage(3) Port A2 Output High Voltage(4) Ports A, D Input Leakage Current I/O Pin Input Leakage Current I/O Pin I/O Pin Pull-up 4.3 2.3 8.0 8.0 35.0 122.0 3.0 1.0 9.0 <1.0 1.2 15.0 2.0 A A k mA mA A A Active Mode, VCC = 3V, 4 MHz Idle Mode VCC = 3V, 4 MHz ICC Power Supply Current Power-down(5), VCC = 3V WDT enabled Power-down(5), VCC = 3V WDT disabled 52 ATTINY28L/V 1062E-10/01 ATTINY28L/V DC Characteristics (Continued) TA = -40C to 85C, VCC = 1.8V to 5.5V (unless otherwise noted) Symbol VACIO IACLK TACPD Notes: Parameter Analog Comparator Input Offset Voltage Analog Comparator Input Leakage Current Analog Comparator Propagation Delay Condition VCC = 5V VIN = VCC/2 VCC = 5V VIN = VCC/2 VCC = 2.7V VCC = 4.0V -50.0 750.0 500.0 Min Typ Max 40.0 50.0 Units mV nA ns 1. "Max" means the highest value where the pin is guaranteed to be read as low. 2. "Min" means the lowest value where the pin is guaranteed to be read as high. 3. Although each I/O port can sink more than the test conditions (20 mA at VCC = 5V, 10 mA at VCC = 3V) under steady-state conditions (non-transient), the following must be observed: 1] The sum of all IOL, for all ports, should not exceed 300 mA. 2] The sum of all IOL, for port D0 - D7 and XTAL2 should not exceed 100 mA. If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions. 4. Although each I/O port can source more than the test conditions (3 mA at VCC = 5V, 1.5 mA at VCC = 3V) under steady-state conditions (non-transient), the following must be observed: 1] The sum of all IOH, for all ports, should not exceed 300 mA. 2] The sum of all IOH, for port D0 - D7 and XTAL2 should not exceed 100 mA. If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current greater than the listed test conditions. 5. Minimum VCC for power-down is 1.5V. 53 1062E-10/01 External Clock Drive Waveforms Figure 40. External Clock VIH1 VIL1 External Clock Drive VCC = 1.8V to 2.7V Symbol 1/tCLCL tCLCL tCHCX tCLCX tCLCH tCHCL Parameter Oscillator Frequency Clock Period High Time Low Time Rise Time Fall Time : VCC = 2.7V to 4.0V Min 0.0 250.0 100.0 100.0 Max 4.0 VCC = 4.0V to 5.5V Min 0.0 250.0 100.0 100.0 Max 4.0 Units MHz ns ns ns 0.5 0.5 s s Min 0.0 833.0 333.0 333.0 Max 1.2 1.6 1.6 1.6 1.6 Table 25. External RC Oscillator, Typical Frequencies R [k] 100.0 31.5 6.5 Note: C [pF] 70.0 20.0 20.0 f 100.0 kHz 1.0 MHz 4.0 MHz R should be in the range 3 - 100 k, and C should be at least 20 pF. 54 ATTINY28L/V 1062E-10/01 ATTINY28L/V Typical Characteristics The following charts show typical behavior. These figures are not tested during manufacturing. All current consumption measurements are performed with all I/O pins configured as inputs and with internal pull-ups enabled. A sine wave generator with railto-rail output is used as clock source. The power consumption in Power-down mode is independent of clock selection. The current consumption is a function of several factors, such as: operating voltage, operating frequency, loading of I/O pins, switching rate of I/O pins, code executed and ambient temperature. The dominating factors are operating voltage and frequency. The current drawn from capacitive loaded pins may be estimated (for one pin) as CL * VCC * f, where CL = Load Capacitance, VCC = Operating Voltage and f = Average Switching Frequency of I/O pin. The parts are characterized at frequencies and voltages higher than test limits. Parts are not guaranteed to function properly at frequencies and voltages higher than the ordering code indicates. The difference between current consumption in Power-down mode with Watchdog Timer enabled and Power-down mode with Watchdog Timer disabled represents the differential current drawn by the Watchdog Timer. Figure 41. Active Supply Current vs. Frequency ACTIVE SUPPLY CURRENT vs. FREQUENCY TA = 25C 18 16 14 12 VCC = 6.0V VCC = 5.5V VCC = 5.0V VCC = 4.5V VCC = 4.0V VCC = 3.6V VCC = 3.3V VCC = 3.0V VCC = 2.7V VCC = 2.4V VCC = 2.1V VCC = 1.8V 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ICC (mA) 10 8 6 4 2 0 Frequency (MHz) 55 1062E-10/01 Figure 42. Active Supply Current vs. VCC ACTIVE SUPPLY CURRENT vs. VCC FREQUENCY = 4 MHz 8 7 6 5 TA = 25C TA = 85C ICC (mA) 4 3 2 1 0 1.5 2 2.5 3 3.5 VCC (V) 4 4.5 5 5.5 6 Figure 43. Active Supply Current vs. VCC, Device Clocked by Internal Oscillator ACTIVE SUPPLY CURRENT vs. Vcc DEVICE CLOCKED BY 1.2MHz INTERNAL RC OSCILLATOR 6 5 TA = 25C 4 TA = 85C I cc(mA) 3 2 1 0 1.5 2 2.5 3 3.5 Vcc(V) 4 4.5 5 5.5 6 56 ATTINY28L/V 1062E-10/01 ATTINY28L/V Figure 44. Active Supply Current vs. VCC, Device Clocked by External 32 kHz Crystal ACTIVE SUPPLY CURRENT vs. VCC DEVICE CLOCKED BY 32 kHz CRYSTAL 4 3.5 TA = 25C 3 TA = 85C 2.5 ICC (mA) 2 1.5 1 0.5 0 1.5 2 2.5 3 3.5 VCC (V) 4 4.5 5 5.5 6 Figure 45. Idle Supply Current vs. Frequency IDLE SUPPLY CURRENT vs. FREQUENCY TA = 25C 4.5 4 3.5 3 ICC (mA) VCC = 6.0V VCC = 5.5V VCC = 5.0V VCC = 4.5V VCC = 4.0V VCC = 3.6V VCC = 3.3V VCC = 3.0V VCC = 2.7V VCC = 2.4V VCC = 2.1V 0 VCC = 1.8V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 2.5 2 1.5 1 0.5 0 Frequency (MHz) 57 1062E-10/01 Figure 46. Idle Supply Current vs. VCC IDLE SUPPLY CURRENT vs. VCC FREQUENCY = 4 MHz 1.4 1.2 TA = 85C 1 0.8 0.6 0.4 0.2 0 TA = 25C ICC (mA) 1.5 2 2.5 3 3.5 VCC (V) 4 4.5 5 5.5 6 Figure 47. Idle Supply Current vs. VCC, Device Clocked by Internal Oscillator IDLE SUPPLY CURRENT vs. Vcc DEVICE CLOCKED BY 1.2MHz INTERNAL RC OSCILLATOR 0.7 0.6 TA = 25C 0.5 0.4 I cc(mA) TA = 85C 0.3 0.2 0.1 0 1.5 2 2.5 3 3.5 Vcc(V) 4 4.5 5 5.5 6 58 ATTINY28L/V 1062E-10/01 ATTINY28L/V Figure 48. Idle Supply Current vs. VCC, Device Clocked by External 32 kHz Crystal IDLE SUPPLY CURRENT vs. VCC DEVICE CLOCKED BY 32 kHz CRYSTAL 30 25 20 TA = 85C TA = 25C ICC (A) 15 10 5 0 1.5 2 2.5 3 3.5 VCC (V) 4 4.5 5 5.5 6 Figure 49. Power-down Supply Current vs. VCC POWER-DOWN SUPPLY CURRENT vs. VCC WATCHDOG TIMER DISABLED 3 TA = 85C 2.5 2 ICC (A) 1.5 TA = 70C 1 0.5 TA = 45C TA = 25C 0 1.5 2 2.5 3 3.5 VCC (V) 4 4.5 5 5.5 6 59 1062E-10/01 Figure 50. Power-down Supply Current vs. VCC POWER-DOWN SUPPLY CURRENT vs. VCC WATCHDOG TIMER ENABLED 70 60 50 40 TA = 25C TA = 85C ICC (A) 30 20 10 0 1.5 2 2.5 3 3.5 VCC (V) 4 4.5 5 5.5 6 Analog comparator offset voltage is measured as absolute offset. Figure 51. Analog Comparator Offset Voltage vs. Common Mode Voltage (VCC = 5V) 18 16 14 Offset Voltage (mV) 12 10 8 6 4 2 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 TA = 25C TA = 85C Common Mode Voltage (V) 60 ATTINY28L/V 1062E-10/01 ATTINY28L/V Figure 52. Analog Comparator Offset Voltage vs. Common Mode Voltage (VCC = 2.7V) 10 TA = 25C 8 Offset Voltage (mV) 6 TA = 85C 4 2 0 0 0.5 1 1.5 Common Mode Voltage (V) 2 2.5 3 Figure 53. Analog Comparator Input Leakage Current (VCC = 6V; TA = 25C) 60 50 40 IACLK (nA) 30 20 10 0 -10 0 0.5 1 1.5 2 2.5 3 3.5 VIN (V) 4 4.5 5 5.5 6 6.5 7 61 1062E-10/01 Figure 54. Calibrated Internal RC Oscillator Frequency vs. VCC CALIBRATED RC OSCILLATOR FREQUENCY vs. OPERATING VOLTAGE 1.28 1.26 1.24 TA = 85C TA = 25C TA = 45C TA = 70C 1.22 FRc (MHz) 1.2 1.18 1.16 1.14 1.12 1.1 2 2.5 3 3.5 4 Vcc(V) 4.5 5 5.5 6 Figure 55. Watchdog Oscillator Frequency vs. VCC 1600 1400 1200 1000 FRC (kHz) 800 600 400 200 0 1.5 2 2.5 3 3.5 VCC (V) 4 4.5 5 5.5 6 TA = 25C TA = 85C 62 ATTINY28L/V 1062E-10/01 ATTINY28L/V Sink and source capabilities of I/O ports are measured on one pin at a time. Figure 56. Pull-up Resistor Current vs. Input Voltage (VCC = 5V) 120 TA = 25C 100 TA = 85C 80 IOP (A) 60 40 20 0 0 0.5 1 1.5 2 2.5 VOP (V) 3 3.5 4 4.5 5 Figure 57. Pull-up Resistor Current vs. Input Voltage (VCC = 2.7V) 30 TA = 25C 25 TA = 85C 20 IOP (A) 15 10 5 0 0 0.5 1 1.5 VOP (V) 2 2.5 3 63 1062E-10/01 Figure 58. I/O Pin Sink Current vs. Output Voltage. All pins except PA2 (VCC = 5V) 70 TA = 25C 60 TA = 85C 50 IOL (mA) 40 30 20 10 0 0 0.5 1 1.5 VOL (V) 2 2.5 3 Figure 59. I/O Pin Source Current vs. Output voltage (VCC = 5V) 20 18 16 14 IOH (mA) 12 10 8 6 4 2 0 0 0.5 1 TA = 25C TA = 85C 1.5 2 2.5 VOH (V) 3 3.5 4 4.5 5 64 ATTINY28L/V 1062E-10/01 ATTINY28L/V Figure 60. I/O Pin Sink Current vs. Output Voltage, All Pins Except PA2 (VCC = 2.7V) 25 TA = 25C 20 TA = 85C 15 IOL (mA) 10 5 0 0 0.5 1 VOL (V) 1.5 2 Figure 61. I/O Pin Source Current vs. Output Voltage (VCC = 2.7V) 6 TA = 25C 5 TA = 85C 4 IOH (mA) 3 2 1 0 0 0.5 1 1.5 VOH (V) 2 2.5 3 65 1062E-10/01 Figure 62. PA2 I/O Pin Sink Current vs. Output Voltage (High Current Pin PA2; TA = 25C) 90 80 70 60 IOL (mA) VCC = 3.6V VCC = 2.4V 50 40 30 20 10 0 0 0.5 1 1.5 2 VOL (V) 2.5 3 3.5 4 VCC = 1.8V Figure 63. I/O Pin Input Threshold Voltage vs. VCC (TA = 25C) 2.5 2 Threshold Voltage (V) 1.5 1 0.5 0 2.7 4.0 VCC 5.0 66 ATTINY28L/V 1062E-10/01 ATTINY28L/V Figure 64. I/O Pin Input Hysteresis vs. VCC (TA = 25C) 0.18 0.16 0.14 Input Hysteresis (V) 0.12 0.1 0.08 0.06 0.04 0.02 0 2.7 4.0 VCC 5.0 67 1062E-10/01 Register Summary Address $3F $3E ... $20 $1F $1E $1D $1C $1B $1A $19 $18 $17 $16 $15 $14 $13 $12 $11 $10 $0F $0E $0D $0C $0B $0A $09 $08 $07 $06 $05 $04 $03 $02 $01 $00 Name SREG Reserved Reserved Reserved Reserved Reserved Reserved Reserved PORTA PACR PINA Reserved Reserved PINB Reserved Reserved Reserved PORTD DDRD PIND Reserved Reserved Reserved Reserved Reserved Reserved Reserved ACSR MCUCS ICR IFR TCCR0 TCNT0 MODCR WDTCR OSCCAL Bit 7 I Bit 6 T Bit 5 H Bit 4 S Bit 3 V Bit 2 N Bit 1 Z Bit 0 C Page page 11 - - - - PORTA3 DDA3 PINA3 PORTA2 PA2HC - PORTA1 DDA1 PINA1 PORTA0 DDA0 PINA0 page 36 page 36 page 37 PINB7 PINB6 PINB5 PINB4 PINB3 PINB2 PINB1 PINB0 page 39 PORTD7 DDD7 PIND7 PORTD6 DDD6 PIND6 PORTD5 DDD5 PIND5 PORTD4 DDD4 PIND4 PORTD3 DDD3 PIND3 PORTD2 DDD2 PIND2 PORTD1 DDD1 PIND1 PORTD0 DDD0 PIND0 page 42 page 42 page 42 ACD PLUPB INT1 INTF1 FOV0 ONTIM4 - INT0 INTF0 ONTIM3 - ACO SE LLIE ONTIM2 - ACI SM TOIE0 TOV0 OOM01 ONTIM1 WDTOE ACIE WDRF ISC11 OOM00 ONTIM0 WDE ISC10 CS02 MCONF2 WDP2 ACIS1 EXTRF ISC01 CS01 MCONF1 WDP1 ACIS0 PORF ISC00 CS00 MCONF0 WDP0 page 34 page 17 page 19 page 20 page 24 page 25 page 29 page 26 page 28 Timer/Counter0 (8-bit) Oscillator Calibration Register Notes: 1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses should never be written. 2. Some of the status flags are cleared by writing a logical "1" to them. Note that the CBI and SBI instructions will operate on all bits in the I/O register, writing a one back into any flag read as set, thus clearing the flag. The CBI and SBI instructions work with registers $00 to $1F only. 68 ATTINY28L/V 1062E-10/01 ATTINY28L/V Instruction Set Summary Mnemonic ADD ADC SUB SUBI SBC SBCI AND ANDI OR ORI EOR COM NEG SBR CBR INC DEC TST CLR SER RJMP RCALL RET RETI CPSE CP CPC CPI SBRC SBRS SBIC SBIS BRBS BRBC BREQ BRNE BRCS BRCC BRSH BRLO BRMI BRPL BRGE BRLT BRHS BRHC BRTS BRTC BRVS BRVC BRIE BRID Rd, Rr Rd, Rr Rd, Rr Rd, K Rr, b Rr, b P, b P, b s, k s, k k k k k k k k k k k k k k k k k k k Operands Rd, Rr Rd, Rr Rd, Rr Rd, K Rd, Rr Rd, K Rd, Rr Rd, K Rd, Rr Rd, K Rd, Rr Rd Rd Rd, K Rd, K Rd Rd Rd Rd Rd k k Description Add Two Registers Add with Carry Two Registers Subtract Two Registers Subtract Constant from Register Subtract with Carry Two Registers Subtract with Carry Constant from Reg. Logical AND Registers Logical AND Register and Constant Logical OR Registers Logical OR Register and Constant Exclusive OR Registers One's Complement Two's Complement Set Bit(s) in Register Clear Bit(s) in Register Increment Decrement Test for Zero or Minus Clear Register Set Register Relative Jump Relative Subroutine Call Subroutine Return Interrupt Return Compare, Skip if Equal Compare Compare with Carry Compare Register with Immediate Skip if Bit in Register Cleared Skip if Bit in Register is Set Skip if Bit in I/O Register Cleared Skip if Bit in I/O Register is Set Branch if Status Flag Set Branch if Status Flag Cleared Branch if Equal Branch if Not Equal Branch if Carry Set Branch if Carry Cleared Branch if Same or Higher Branch if Lower Branch if Minus Branch if Plus Branch if Greater or Equal, Signed Branch if Less than Zero, Signed Branch if Half-carry Flag Set Branch if Half-carry Flag Cleared Branch if T-flag Set Branch if T-flag Cleared Branch if Overflow Flag is Set Branch if Overflow Flag is Cleared Branch if Interrupt Enabled Branch if Interrupt Disabled Operation Rd Rd + Rr Rd Rd + Rr + C Rd Rd - Rr Rd Rd - K Rd Rd - Rr - C Rd Rd - K - C Rd Rd * Rr Rd Rd * K Rd Rd v Rr Rd Rd v K Rd Rd =Rr Rd $FF - Rd Rd $00 - Rd Rd Rd v K Rd Rd * (FFh - K) Rd Rd + 1 Rd Rd - 1 Rd Rd *=Rd Rd Rd =Rd Rd $FF PC PC + k + 1 PC PC + k + 1 PC STACK PC STACK if (Rd = Rr) PC PC + 2 or 3 Rd - Rr Rd - Rr - C Rd - K if (Rr(b) = 0) PC PC + 2 or 3 if (Rr(b) = 1) PC PC + 2 or 3 if (P(b) = 0) PC PC + 2 or 3 if (P(b) = 1) PC PC + 2 or 3 if (SREG(s) = 1) then PC PC + k + 1 if (SREG(s) = 0) then PC PC + k + 1 if (Z = 1) then PC PC + k + 1 if (Z = 0) then PC PC + k + 1 if (C = 1) then PC PC + k + 1 if (C = 0) then PC PC + k + 1 if (C = 0) then PC PC + k + 1 if (C = 1) then PC PC + k + 1 if (N = 1) then PC PC + k + 1 if (N = 0) then PC PC + k + 1 if (N V = 0) then PC PC + k + 1 if (N V = 1) then PC PC + k + 1 if (H = 1) then PC PC + k + 1 if (H = 0) then PC PC + k + 1 if (T = 1) then PC PC + k + 1 if (T = 0) then PC PC + k + 1 if (V = 1) then PC PC + k + 1 if (V = 0) then PC PC + k + 1 if (I = 1) then PC PC + k + 1 if (I = 0) then PC PC + k + 1 Flags Z,C,N,V,H Z,C,N,V,H Z,C,N,V,H Z,C,N,V,H Z,C,N,V,H Z,C,N,V,H Z,N,V Z,N,V Z,N,V Z,N,V Z,N,V Z,C,N,V Z,C,N,V,H Z,N,V Z,N,V Z,N,V Z,N,V Z,N,V Z,N,V None None None None I None Z,N,V,C,H Z,N,V,C,H Z N,V,C,H None None None None None None None None None None None None None None None None None None None None None None None None # Clocks 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 3 4 4 1/2 1 1 1 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 ARITHMETIC AND LOGIC INSTRUCTIONS BRANCH INSTRUCTIONS 69 1062E-10/01 Instruction Set Summary (Continued) Mnemonic LD ST MOV LDI IN OUT LPM BIT AND BIT-TEST INSTRUCTIONS SBI CBI LSL LSR ROL ROR ASR SWAP BSET BCLR BST BLD SEC CLC SEN CLN SEZ CLZ SEI CLI SES CLS SEV CLV SET CLT SEH CLH NOP SLEEP WDR P, b P, b Rd Rd Rd Rd Rd Rd s s Rr, b Rd, b Set Bit in I/O Register Clear Bit in I/O Register Logical Shift Left Logical Shift Right Rotate Left through Carry Rotate Right through Carry Arithmetic Shift Right Swap Nibbles Flag Set Flag Clear Bit Store from Register to T Bit Load from T to Register Set Carry Clear Carry Set Negative Flag Clear Negative Flag Set Zero Flag Clear Zero Flag Global Interrupt Enable Global Interrupt Disable Set Signed Test Flag Clear Signed Test Flag Set Two's Complement Overflow Clear Two's Complement Overflow Set T in SREG Clear T in SREG Set Half-carry Flag in SREG Clear Half-carry Flag in SREG No Operation Sleep Watchdog Reset (see specific descr. for Sleep function) (see specific descr. for WDR/timer) I/O(P,b) 1 I/O(P,b) 0 Rd(n+1) Rd(n), Rd(0) 0 Rd(n) Rd(n+1), Rd(7) 0 Rd(0) C, Rd(n+1) Rd(n), C Rd(7) Rd(7) C, Rd(n) Rd(n+1), C Rd(0) Rd(n) Rd(n+1), n = 0..6 Rd(3..0) Rd(7..4), Rd(7..4) Rd(3..0) SREG(s) 1 SREG(s) 0 T Rr(b) Rd(b) T C1 C0 N =1 N0 Z1 Z0 I1 I0 S1 S0 V= 1 V0 T= 1 T =0 H1 H0 None None Z,C,N,V Z,C,N,V Z,C,N,V Z,C,N,V Z,C,N,V None SREG(s) SREG(s) T None C C N N Z Z I I S S V V T T H H None None None 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Operands Rd, Z Z, Rr Rd, Rr Rd, K Rd, P P, Rr Description Load Register Indirect Store Register Indirect Move between Registers Load Immediate In Port Out Port Load Program Memory Operation Rd (Z) (Z) Rr Rd Rr Rd = K Rd P P Rr R0 =(Z) Flags None None None None None None None # Clocks 2 2 1 1 1 1 3 DATA TRANSFER INSTRUCTIONS 70 ATTINY28L/V 1062E-10/01 ATTINY28L/V Ordering Information Speed (MHz) 4 Power Supply (Volts) 2.7 - 5.5 Ordering Code ATTINY28L-4AC ATTINY28L-4PC ATTINY28L-4MC ATTINY28L-4AI ATTINY28L-4PI ATTINY28L-4MI 1.2 1.8 - 5.5 ATtiny28V-1AC ATtiny28V-1PC ATtiny28V-1MC ATtiny28V-1AI ATtiny28V-1PI ATtiny28V-1MI Package 32A 28P3 32M1-A 32A 28P3 32M1-A 32A 28P3 32M1-A 32A 28P3 32M1-A Operation Range Commercial (0C to 70C) Industrial (-40C to 85C) Commercial (0C to 70C) Industrial (-40C to 85C) Package Type 32A 28P3 32M1-A 32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP) 28-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 32-pad, 5x5x1.0 body, Lead Pitch 0.50mm Micro Lead Frame Package (MLF) 71 1062E-10/01 Packaging Information 32A 32-lead, Thin (1.0mm) Plastic Quad Flatpack (TQFP), 7x7mm body, 2.0mm footprint, 0.8mm pitch. Dimensions in Millimeters and (Inches)* JEDEC STADARD MS-026 ABA PIN 1 ID 9.25 (0.364) 8.75 (0.344) 0.45 (0.018) 0.30 (0.012) PIN 1 9.25 (0.364) 8.75 (0.344) 0.80 (0.0315) BSC 7.10 (0.280) 6.90 (0.272) SQ 1.20 (0.047) MAX 0.20 (0.008) 0.09 (0.004) 0~7 0.75 (0.030) 0.45 (0.018) 0.15 (0.006) 0.05 (0.002) *Controlling dimensions: Millimeters 72 ATTINY28L/V 1062E-10/01 ATTINY28L/V 28P3 28-lead, Plastic Dual Inline Package (PDIP), 0.300" Wide, (0.288" body width) Dimensions in Millimeters and (Inches)* 34.80(1.370) 34.54(1.360) 7.49(0.295) 7.11(0.280) 4.57(0.180)MAX 3.56(0.140) 3.05(0.120) 2.54(0.100)BSC 1.65(0.065) 1.27(0.050) 0.56(0.022) 0.38(0.015) 8.26(0.325) 7.62(0.300) 0~ 15 REF 0.38(0.015) 10.20(0.400)MAX *Controlling dimension: Inches REV. A 04/11/2001 73 1062E-10/01 32M1-A D D1 PIN #1 ID 1 2 3 E1 E 0 TOP VIEW A2 P D2 A A3 A1 PIN 1 ID P 1 2 3 E2 SIDE VIEW 0.08 C COMMON DIMENSIONS (*Unit of Measure = mm) SYMBOL A A1 A2 A3 b e BOTTOM VIEW b L D D1 D2 E NOTE 1. JEDEC STANDARD MO-220, Fig 2 (Anvil Singulation), VHHD-2 E1 E2 e L P 0 MIN 0.80 0.00 0.18 NOM 0.90 0.02 0.65 0.20 REF 0.23 5.00 BSC 4.75 BSC MAX 1.00 0.05 1.00 0.30 NOTE 1.25 5.00 BSC 4.75 BSC 3.25 1.25 0.50 BSC 3.25 0.30 - 0.40 - 0.50 0.60 12 REV R 06/27/01 DRAWING NO. 2325 Orchard Parkway TITLE 32M1-A, 32-pad, 5x5x1.0mm body, Lead Pitch 0.50mm San Jose, CA 95131 32M1-A Mirco Lead Frame package (MLF) A 74 ATTINY28L/V 1062E-10/01 Atmel Headquarters Corporate Headquarters 2325 Orchard Parkway San Jose, CA 95131 TEL (408) 441-0311 FAX (408) 487-2600 Atmel Product Operations Atmel Colorado Springs 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL (719) 576-3300 FAX (719) 540-1759 Europe Atmel SarL Route des Arsenaux 41 Casa Postale 80 CH-1705 Fribourg Switzerland TEL (41) 26-426-5555 FAX (41) 26-426-5500 Atmel Grenoble Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France TEL (33) 4-7658-3000 FAX (33) 4-7658-3480 Atmel Heilbronn Theresienstrasse 2 POB 3535 D-74025 Heilbronn, Germany TEL (49) 71 31 67 25 94 FAX (49) 71 31 67 24 23 Asia Atmel Asia, Ltd. Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimhatsui East Kowloon Hong Kong TEL (852) 2721-9778 FAX (852) 2722-1369 Atmel Nantes La Chantrerie BP 70602 44306 Nantes Cedex 3, France TEL (33) 0 2 40 18 18 18 FAX (33) 0 2 40 18 19 60 Japan Atmel Japan K.K. 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL (81) 3-3523-3551 FAX (81) 3-3523-7581 Atmel Rousset Zone Industrielle 13106 Rousset Cedex, France TEL (33) 4-4253-6000 FAX (33) 4-4253-6001 Atmel Smart Card ICs Scottish Enterprise Technology Park East Kilbride, Scotland G75 0QR TEL (44) 1355-357-000 FAX (44) 1355-242-743 literature@atmel.com Web Site http://www.atmel.com BBS 1-(408) 436-4309 (c) Atmel Corporation 2001. Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company's standard warranty which is detailed in Atmel's Terms and Conditions located on the Company's web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel's products are not authorized for use as critical components in life support devices or systems. ATMEL (R) and AVR (R) are the registered trademarks of Atmel. Other terms and product names may be the trademarks of others. Printed on recycled paper. 1062E-10/01/xM |
Price & Availability of ATTINY28L
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |